Activity Stream

It has some resemblance to the Cincinnati heads, and a little bit of the Walter look, but different. Really just a bump to put your post back in...

You'll need a very pure colour to get an interference pattern with high contrast. This is the spectra of your specific Vialox NAV-T lamp puts out:...

Colchester shows an interesting test bar in an early manual. The bar is a long one of smaller but sturdy diameter and has largish pucks pressed or...

That Kiwi hasn't been here in about 5 years.I wouldn't expect an answer any time soon.

I also advise against full penetration TIG on the splits....TIG deposit will be far harder and tougher than the soft iron of the barrel,and may cause...

Bill, Sorry for he double post. I did the first one and it didn't show up so I thought it got lost in space. I eliminated one when I saw your...

Did you manage to find the missing pitches? If so how? cheers, UNCLE CHUFTY

JTB3, Yeah the settings that I posted are straight from the manual for brass to steel so I'm not really sure where to go from here.

The " Zeus " pocket book was what we used all the time. I also have a little circular plastic double sided pocket device with a cursor that gave you...

if you get a taper, you can always use the compound to compensate. easier than relevelling the lathe for every part your making.

I would have thought that an electronic height gage would be a good investment for such a place. Accuracy for surfaces is 2 microns or so - about 7...

You want numbers,look them up. The vast majority of these people are not refugees they are economic migrants. If they are refugees why do they...

How is your Mitutoyo QM height gage going? Went to see one at the local dealer and it looks good. I'm looking to purchase a height gage. Had a...

Tannewitz, I tried to send you a message but your PM inbox is full. Good luck with the sale Ed, I love my 1030F. The D1-3 spindle makes yours...

Copied from my book (page 72) for further explanation ... "It is important to note that a Boolean value TRUE is not equivalent to the arithmetic...

I was taking the medication that shrinks your prostate for about 10 years. Last year the specialist told me that it isn't a permanent cure and...

Google works for me every time, i do have some pages laminated out of a old OSG catalogue on some cupboard doors for all the tap sizes i could wish...

My nurse wife, who knows not a thing mechanical, tends to roll her eyes when I tell her with the right service manual I could be a doctor, haha. ...

I have seen similar when cleaning chemicals were incorrectly mixed + low grade stainless. That dribble down like pattern is typical of some of the...

Sounds like you've had a tough time Joe. I'm pleased you seem to be on the mend. Immediately after my operation they put really tight knee high...

the bulb puts out a very yellow/orange light: VIALOX NAV-T SUPER 4Y NAV-T 5W SUPER | OSRAM DS how much better will it be with the sox? ...

Four or five years ago I had a redcap behave exactly like that - turned out to be the pulse coder. I was hesitant to accept that was the problem as I...

yes, I know this is a very old thread. I have a 1936 monarch AA 14 x 30. I don't know about the flame-hardened ways, because I haven't seen any tags...

Not sure the weight of 10's, but a 16" will be about 2600- 2800 lbs. While I could be wrong, I thought a heavy 10 had it's own motor base like a 13",...

Since you have to do "a lot", regardless of the path taken, I'd go for maximizing the return on all that cost and effort. My vote would be to go...

Who said it was even inside the machine? :D Seriously, that isn't as hard as you might think. First of all, they can be a seriously tiny...

note on the high (fast) helix drills, the high helix also changes the cutting edge geometry - if you imagine the cross section of the cutting edge,...

The motor is in a Monarch 10EE "manufacturing" lathe, though I did not get any of the drive components and all the controls were gone. Most of the...

so how is the fit in the bore?