alphonso
Titanium
- Joined
- Feb 15, 2006
- Location
- Republic of Texas
Fanuc 18MC, Cutter Compensation "C".
Program for threadmilling. New threadmill is slightly smaller OD(.347 as opposed to .35), thus threads are too tight. Thought that we would add comp to program rather than re-post or calculate how much to change values.
Not having any luck, keep getting 034 error.
So, can somebody show me what and where to add G41, D value(112), and G1 lead in? The X-1 Y0 is the position to start threadmilling the first hole.
N310 T12 (1/2 X 13 THREADMILL) M6
N320 G54
N330 G0 G90 X-1.0 Y.0 S4365 M3
N340 G43 Z.2 H12 T15
N350 G72.2 P0071 L3 I1.
N470 M09
N480 M05
N490 G28 G40 G91 Z.0 M09
N500 G28 Y.0
N510 G90
N520 M30
:0071 (SUB FOR 0070)
N370 G1 Z-.8192 F13.1 M8
N380 G3 X-.9435 Y.0 Z-.8 I.0283 J.0 F3.1972
N390 G3 X-.9435 Y.0 Z-.7231 I-.0565 J.0
N400 G40 G3 X-1.0 Y.0 Z-.7038 I-.0283 J.0
N410 G1 Z-.8192 F13.1
N420 G3 X-.9225 Y.0 Z-.8 I.0388 J.0 F4.0208
N430 G3 X-.9225 Y.0 Z-.7231 I-.0775 J.0
N440 G3 X-1.0 Y.0 Z-.7038 I-.0387 J.0
N450 G0 Z.2
N460 M99
Program for threadmilling. New threadmill is slightly smaller OD(.347 as opposed to .35), thus threads are too tight. Thought that we would add comp to program rather than re-post or calculate how much to change values.
Not having any luck, keep getting 034 error.
So, can somebody show me what and where to add G41, D value(112), and G1 lead in? The X-1 Y0 is the position to start threadmilling the first hole.
N310 T12 (1/2 X 13 THREADMILL) M6
N320 G54
N330 G0 G90 X-1.0 Y.0 S4365 M3
N340 G43 Z.2 H12 T15
N350 G72.2 P0071 L3 I1.
N470 M09
N480 M05
N490 G28 G40 G91 Z.0 M09
N500 G28 Y.0
N510 G90
N520 M30
:0071 (SUB FOR 0070)
N370 G1 Z-.8192 F13.1 M8
N380 G3 X-.9435 Y.0 Z-.8 I.0283 J.0 F3.1972
N390 G3 X-.9435 Y.0 Z-.7231 I-.0565 J.0
N400 G40 G3 X-1.0 Y.0 Z-.7038 I-.0283 J.0
N410 G1 Z-.8192 F13.1
N420 G3 X-.9225 Y.0 Z-.8 I.0388 J.0 F4.0208
N430 G3 X-.9225 Y.0 Z-.7231 I-.0775 J.0
N440 G3 X-1.0 Y.0 Z-.7038 I-.0387 J.0
N450 G0 Z.2
N460 M99