Results 1 to 20 of 78
Thread: Smallest full-on CNC shop Ever?
07-14-2011, 08:00 AM #1
Smallest full-on CNC shop Ever?
Hello everyone, a lot of people have been asking me to post some pictures of my shop. This whole setup fits in my 650 square ft. garage. This shop has been 3 years in the making and still growing....right out the door into a bigger one within the year if orders keep coming in (finger's crossed)! Enjoy!
Budget Air dryer
Hardinge HTC 1970ish
real mist collector are expensive, this work great!
2011 Hurco VM10, My first VMC
1987 Okuma LB 12 Turning Center, my diamond in the rough! This thing holds tenths all day long! Flawless turning.
Pictures by proturn - Photobucket
Last edited by proturn; 07-15-2011 at 07:12 AM.
07-14-2011, 10:51 AM #2
Looking good. Small but filled with nice equipment. The first shop I worked at had about that vintage of Okuma and she would hog tool steel all day.
How do you like the VM10? I run a VMX42 and it can piss me off at times but is overall a nice machine. I'm used to G-code and want the machine to do what I say, not what it thinks I want it to do. I ask because I would like to get a small VMC and am trying to decide between Sharp, Haas, & Hurco.
07-14-2011, 11:07 AM #3
I like the VM10. It has a lot of very handy features, my favorite is tool optimization. ‪HURCO VM10 MILLING 6061 ALUMINUM 102.MOV‬‏ - YouTube
you can see how it works on these parts. It minimizes tool changes.
07-14-2011, 11:40 AM #4
Sweet little cozy machine shop!
Im going to pm you about a job im thinking of sourcing out.
proturn liked this post
07-15-2011, 10:31 AM #5
Awsome looks so cool keep going till it gets to be no fun!
07-15-2011, 10:40 AM #6
Neat layout...is it bad form to ask you what you and your machines make on a daily basis.
07-15-2011, 11:06 AM #7
Neat, compact shop. I'm in the same boat for space. Couple of questions..
What do you have for power (how many amp service)? What kinda of phase converter?
What kind of compressor(screw or piston, and how big)? How do they (machines and machines and compressor) interact? Can you run multiple machines at once and also the compressor?
All the questions, because I'm about to find out...
Thanks in advance,
07-16-2011, 10:43 AM #8
On mist collection:
That's a really good start to liquid recovery, and nearly exactly how we pull mist out of natural gas streams. You may get better recovery by enlarging pipe diameter on the vertical runs. The larger flow area makes for a drop in linear velocity and the liquids will fall out. Also, have you packed those same runs with anything, or are they empty pipe? We use a stainless steel mesh pad in the bottom of our scrubbers as a primary collection point.
Here's a pic of the vessels I'm referring to, see the resemblance?
Inlet nozzle on the right, outlet nozzle on top. The silver insulated piping on the bottom right of the vessel is the drain.
PS: If you want to get technical with it I can run some numbers when I get back to the office monday.
Last edited by Cole2534; 07-16-2011 at 10:46 AM. Reason: Added offer.
07-17-2011, 10:22 AM #9
That is really nice. I love that Hurco.
Is the Okuma similar to what Wrustle just purchased a while back?
Gonna have to work myself up an air dryer like that.
Great idea on the range hood mist collector, I like using equipment for purposes not intended.
07-17-2011, 10:27 AM #10
Ikegai limit problem
First post...may be in the wrong area nut please help.]
I need urgent help please. I got CNC LATHE IKEGAI with fanuc controls Series 18-T
Problem is with the Z Limit switch. I had some issue with over load that i fixed by moving the mottor coupling by hand but thereafter I was getting ALM about over travel. That related to the limit switch so i moved the Z axis somewhere in the center of the machine to get access to limit switch. While doing Zero return at this stage i Pressed the limit switch manually to check it its working. It worked fine and i saw Z limit light on. But the problem now is that Z Limit is right there all the time i.e. somewhere in the middle of the machine .I think machine has registered that location into its memory thus giving me this error . Since there is no physical stop present at that location so machine gives me ALM for over travel and thats logical.
Could someone tell me how to reset the parameters for Z limit switch in System. I know the problem theoritically but could not fine the solution reading the manuals etc.
Any help would be highly appreciated ...i am badly stuck.
07-17-2011, 01:22 PM #11
I wish I could help you, but I don't know anything about those machines.
Some guys here know a lot about CNC lathes, & some own Ikegai lathes.
If you would put this in the CNC forum at the very top of the page you will get help.
Here is a pic of the location. I put a green arrow on the CNC section :
Welcome to Practical Machinist
07-17-2011, 11:45 PM #12
07-17-2011, 11:53 PM #13
The range hood mist collector works really good too. The lathe used to fill the shop with mist and smoke. This cures that problem. My lungs might last a few years more now!
07-17-2011, 11:58 PM #14
07-18-2011, 03:12 AM #15
Sheesh that reminds me of our first 5 years we had 450sqft with a Fadal 3016, 14" swing lathe, 2 bridgeports, one horizontal cnc, a bathroom, a bandsaw, a air compressor nd shelving...we had ant trails. It never dawned on me that we needed to go bigger until a old shop owner who owned a huge screw machine shop happened to be driving by while we had a door open. I will never forget his words he said "That kid will never stand a chance". It made me realize I could putz with small potatos hoping to someday make enough to pay a decent wage or I could grow....the growing helped.
08-07-2011, 06:51 AM #16
Close but no cigar!
Neat shop but we have more in just abit more than you...
See linky #2
OT: Boris has new toys
Excuse the mess- it's not usually like that (it's worse )
Thats 3x chevalier cnc's in a row (2x 850, 1x 660 with swarf conveyor). That's the length of the place, with only 10 feet on the end for mtl.
We also have a robodrill, cnc lathe, and a prototrak mill + prototrak lathe, a schaublin toolroom lathe and eagle surface grinder.
All in 850 square feet
Upstairs (small mez/offices) is inspection (with cmm) + 2x cad cam seats.
08-08-2011, 02:33 AM #17
Nice cozy setup. I know the feeling. When I first started my shop I rented a small "room" basically. I had a turning center, bridgeport, manual lathe, pedestal grinder, two roller chests, and a small saw in a 12X24 space. It was tight.
09-11-2011, 12:39 PM #18
Very nice, very well though out.
I have a manual shop I use to learn with and am going to make a change over to CNC. I have a very good machinist who is helping me learn. I have taken some classes at the local Junior College and learned to stay away from HAAS. Great to learn principles on but not for me. I'd like a Kiti or a Hurco.
I Looked at a new VM10 almost $54 K bare bones. They have a promotion until the end of Sept that would allow an upgrade to their 'Classic' software package at that price. Other than that, with the options I'd need it was pushing 63K.
I could dig up that much dough but it would leave me without any other stuff in the budget. What did you do for 3PH power? What about air? Although my neighborhood is a 5 acre minimum, I still prefer to not have my neighbors subjected to a piston compressor so I want a rotary.
If you do not mind sharing with us, what was your strategy to finance what you needed for a start up?
I also am looking at a used Takisawa Lathe ('91) that's 17K with a new spindle. My mentor is extremely familiar with this manufacturer and the model.
I have a General Contractor's License and could really build on to my garage with no problems other than the cash to do so. I also have a pretty good education that gives me the opportunity to teach at the University level part-time (when the state has a budget that funds education which currently, it does not). That allows me to make payments on the equipment until my start up is sustaining them.
How many hours a week are you in your shop? Is it air conditioned?
Sorry for the lame questions I am fascinated by this example of self-reliance and planning + execution!!!
Very much appreciated that you posted a look-see.
thanks very much,
09-11-2011, 09:50 PM #19
You work as much as you want to grow. Air conditioning depends on your needs, but I would recommend it. My strategy was to work two full time jobs until the business could support itself. I'll defend HAAS since I own a bunch, as do I Hardinge, and Fadal. They all work just fine. Get yourself a big rotary phase converter.
09-16-2011, 11:36 PM #20