Largest Manufacturing Technology Community on the Web
Stay Connected:
Recent content by BenTerrible
-
Dynapath Delta 20 Power Supply Failure
Thank you! This will help me out!- BenTerrible
- Post #3
- Forum: General
-
Dynapath Delta 20 Power Supply Failure
Tried to power up my Tree 325 last weekend. Received a dead battery error at start up (locked out of the control). Replaced the 3.6v battery that is on the Aux board in the Dynapath Delta 20 controller. Powered on the machine, checksum pass, diagnostics pass... Display read "Press Mode...- BenTerrible
- Thread
- Replies: 3
- Forum: General
-
Equipment Moving-Pick up at residence, East to West Haul
I am considering purchasing a small press brake located on the East coast. The seller has the press at his residence, no forklift/not palletized (this is a small machine, 1600 lbs). I have searched high and low for one local/closer, nothing worth much more than it's weight in scrap...- BenTerrible
- Thread
- Replies: 9
- Forum: Material Handling and Rigging
-
WTB Okuma Cadet LNC8
Still searching...the LNC-8-M with live tooling is what I am after.- BenTerrible
- Post #2
- Forum: Machinery for Sale or Wanted
-
Looking for equipment mover San Jose to San Diego
Can anyone recommend a machinery mover? I need quotes getting a turning center from San Jose to San Diego. I am trying to have a rigger on-site when the seller's new machine arrives, as they have offered to load the one I purchased. Thanks in advance! -BT- BenTerrible
- Thread
- Replies: 6
- Forum: General
-
WTB Okuma Cadet LNC8
Looking for a clean Okuma LNC8. Options I am interested in are as follows (they are wishlist items): 5020 control with IGF Big Bore Spindle Chip Conveyor Parts Catcher Tailstock Live Tooling I am open to machines that are not local to me (San Diego). Let me know what you have! -BT- BenTerrible
- Thread
- Replies: 1
- Forum: Machinery for Sale or Wanted
-
Okuma LNC-8 School me on these machines!
Appreciate the feedback. I have my eye on a few LNC8 machines, both local and out of state. Having a hell of time trying to get these machinery brokers to actually respond/answer basic questions regarding their respective machines. Seems the dealers that have these listed haven't got a clue of...- BenTerrible
- Post #4
- Forum: Okuma
-
Okuma LNC-8 School me on these machines!
Considering a small turning center. I have my eye on a few, but the Okuma LNC-8 caught my attention. 1. Controls - The machine I am looking at I believe has the OSP5020 control. Feedback on this control? I hear Okuma machines are those that users either love.or hate. I have yet tonuse one...- BenTerrible
- Thread
- Replies: 4
- Forum: Okuma
-
Waldmann HGW-70 Waterproof Machine Light - German made
I will take this.- BenTerrible
- Post #2
- Forum: Tooling, Parts and Accessories For Sale or Wanted
-
Trico Spraymaster II - About ready to toss this thing into the trash!
I suppose my initiation of this thread was purely out of frustration. After further review of the Trico instructions, I read the "DO NOT" section... "DO NOT use volatile or harmful chemicals in the Trico Spraymaster..." I decided to bathe the nozzle in a pool of diesel fuel and PB Blaster...- BenTerrible
- Post #4
- Forum: General
-
Trico Spraymaster II - About ready to toss this thing into the trash!
Been fighting with this device all day. Can't get coolant flowing for the life of me. These things are siphon systems, which is cost-effective, I get it, but really stupid in my opinion. I would rather have a dedicated pump to push coolant and mix with air at the nozzle. I have cleaned the...- BenTerrible
- Thread
- Replies: 3
- Forum: General
-
Anilam Mini Wizard DRO - Scale not reading
I believe this is an A10 system. I will grab some photos later today for clarification. The label on the scale reads "System A", the label on the readers are "A10". The DRO is a Miniwizard. Appreciate the help! Looking at new scales/readers for replacement. This might get pricey!- BenTerrible
- Post #3
- Forum: General
-
Anilam Mini Wizard DRO - Scale not reading
I have an Anilam Mini Wizard DRO on my Bridgeport and I am having trouble with the Y-axis readout. I fear I need to spend the money on new Acu-rite scales, but I am hoping this isn't the case. The Y-axis suddenly stopped counting. Running the Y-axis in/out, the DRO flickers. No counting, just...- BenTerrible
- Thread
- Replies: 3
- Forum: General
-
WTB Kwik Switch 300 Master with R8 shank for Bridgeport
Looking for a Kwik Switch 300 master with the R8 shank so I can adapt all my tooling to my Bridgeport mill. Thanks! -BT- BenTerrible
- Thread
- Replies: 1
- Forum: Tooling, Parts and Accessories For Sale or Wanted
-
Dynapath Delta 20 drip feeding program error "next character not N"
Appreciate the input. If I remember correctly, Baudrate is set at 4800 currently. I was given settings when I purchased the machine. I will double check later this afternoon.- BenTerrible
- Post #7
- Forum: CNC Machining