I need some suggestions for sources of 305 sheet. I'm looking for annealed material in the thickness range of 0.035 and 0.060. I need pieces that are, say, 2 x 4 feet. My shop makes prototype surgical instruments and I need the formability of 305 and its ability to not work-harden. I've done...
Just checked my MS 850 manual. The distance from spindle center to the top of the saddle is not given as a spec. The distance from center to top of way is 215mm. That's really not accurate enough for setting tool height.
There are lotsa methods for setting tool height which do not involve...
Been using my MS 850 for 8 years now. I have not experienced that problem. Cleaned and re-adjusted the saddle gibs 2-3 years ago and experienced no change, although I went way tighter. The saddle is still effortless to move. I can creep up on a tenth with a gentle rap of my knuckle on the...
I like the paraffin wax idea! I always have a few blocks of it around in the shop. I consider it "the secret weapon" for some obscure problems.
Thanks a lot! I will try to remember to not do it while the machine is running.
Walter
Bill,
Thanks! I'm applying all your suggestions except the last. Good thing I didn't get a Powermatic! I wondered about Alzmetall; there are always a few on eBay.
Here is the progess on the vintage Clausing drill press: It works!!
I did know that the thing was a dual-voltage single phase motor. I pulled the birds-nest of wires out of the motor junction box and my first response was brain-lock!
Then I consulted YouTube, searching for "dual voltage...
Good suggestion, especially the lemonade part!
Not being an electrical engineer (wish I was!), I'd just like the motor shop to pronounce the thing dead or alive. More power, or especially less speed, or even 3ph 240V would be fine with me. And there is always eBay . . . for a new motor...
Yup,
They are nice folks. I've spent a lot of time with them on the phone to figure out part numbers for this old drill press. I just talked to them again today and they recommended that I take the motor to a motor shop and have them look at it. Plus they provided me with the correct manual for...
Hello,
I recently took delivery of a used Clausing Series 22V drill press in pretty good condition for the price: no spindle sloppiness, no evil bearing noises, only one small hole in the table. It has a 110V 1ph motor, 1725 RPM. It has a new variable speed drive belt, and it's been sitting...
lazz,
At one time, I had to drill #80 holes through 1/2 dia 304 stainless balls. It was for a medical device application, where one is frequently drilling tiny holes.
Here are some answers:
-lube is very important; try TapMatic Gold as a good all-round lube; brush it onto the drill and at the...
Hi Everybody,
I have Mori Seiki 850 with and old Royal 5C collet closer setup. In the past, working with the same system, I rember having a wedge to tap into the space between the flange of the insert and the nose of the spindle to pop the insert out.
It seems a better idea to have a pair of...
Hi there,
I have a Mori 850 equipped with an old manual Royal 5C collet closer. The 6MT spindle sleeve that takes the 5C collets is stuck in the spindle.
I have seen photos of pairs of wedges which you squeeze together with a big C clamp to pry the thing out. The wedges are C-shaped with a...
Howdy everybody,
Recently bought a BP Series 1 of 1993 vintage on eBay. Machined appeared to be properly shipped, looked in good condition as far as ways, lube, power feed, weel maintainained.
Wired it up today, and turned it on. SOUNDS LIKE ROCKS FLYING AROUND IN THE HEAD. SPEED IS ALL OVER...
I have located a nice looking Sharp machine from a good seller in Lancaster Co, PA. I really wanna buy it.
The problem is I am getting shipping quotes of above $3k. In the recent past, I was getting quotes of around of $1000 for more weight for approximately the same run. But I have lost the...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.