What's new

Recent content by Cooperstock

  1. C

    FS: Nardini 25160 Gap bed lathe with chucks, rests, large boring bar etc

    Hello, I am selling my Nardini Lathe. It is in fair condition, The feed gear needs to be replaced (the bronze one in the carriage) it was stripped before I had it. I have just used it manually. The threading gears work. 208 3 phase motor. asking $9,200 (lathe + chucks + steady rest & follower +...
  2. C

    Matsurra MC-760VX start up problem, may be controller or powersupply?

    The strange part is that there is no Alarm codes. The machine appears to think its working, I just can't jog the machine, which also means it doesn't zero since it uses the Jog motion to move to the limit switches. I removed the power supply and inspected for burn components, and blew it out...
  3. C

    Matsurra MC-760VX start up problem, may be controller or powersupply?

    I looked for black things, 30 amps would be pretty major, It appears the 112CR relay on the relayboard is what controls the clamp unclamp, I removed it so it wouldn't happen again. I guess it is a possibility the out-going line is exposed some where. I agree, it seems like a symptom, but not...
  4. C

    Matsurra MC-760VX start up problem, may be controller or powersupply?

    Hello, Alright trouble shooting guys, Im trying to track down what possibly is a wiring issue, or maybe a power supply issue, or maybe just a control signal issue... So I have had my MC-760VX up and running for a while now (4 ish years). Yasnac controller. I went to start it up yesterday and...
  5. C

    WTB ~13" Lathe and manual Mill for small Business

    Hello, I have been asked to do some digging for some 'small' machines for my day job. We are looking for a knee mill, manual. DRO would be nice, not necessary. 3 Phase is preferred. Collets, chucks would be handy as a package but not necessary. Manual Lathe, something around the 13"x42" size. 3...
  6. C

    Mazak Integrex 30Y parting out, mostly complete machine

    Yea I was hoping to revive it, it seemed in good condition. I think it was a doner machine for another one they had, but thats just a guess.
  7. C

    Mazak Integrex 30Y parting out, mostly complete machine

    Hello All, Well I decided not to attempt to revive this machine. It makes me sad to part it out, but I simply don't have the time needed to try to get it running. I had started down the 'revive' path, and put together the controller and gathered manuals but I have too much going on to continue...
  8. C

    For sale: Mazak integrex 30Y, for rebuild/parts

    I was working on putting this machine back together but simply don't have time. [I wasnt sure if this goes in parts or machines, i apologize if it should be in parts] I have attached pictures of the machine. It has the drives and motors, i have a controller for it (not shown in pics), I'd be...
  9. C

    Right angle head disassembly?

    I understand it may be an exersize in futility. Id like to see how bad it actually is. You were right. Bolt in the back after removing pull stud Stripped gears. Going to see how hard it is to get those replaced Anyone want to quote some gears?
  10. C

    Right angle head disassembly?

    Hello, I picked up a dented right angle head Manufacturer is OMG its am italian company Im not sure how to disassemble it. It appears one would remove the 6 screws on the back of the head and it clamshell would split apart. I understand this may be the case and the damage prevents the...
  11. C

    Where does SFM number come from?

    You can kind of see the clamping groove here.
  12. C

    Where does SFM number come from?

    Here are the two parts. The small ring is .118 thick. They clamp together to hold a tungsten mesh.
Top