We have a Grob 4v-24 bandsaw that will not stay in high gear. It will grab for a second, then immediately kick back in low.I was wondering if anyone has tear the gearbox apart to see what the culprit is?
The drive is double voltage, 115v AC- =90v dc, 230ac = 180dc. Its been wired that way since 1988, so I don't really see a need to change it. That being said, I ordered a Minerik drive that has a 115v doubler function, and will output 180v dc on. The drive out output voltage would drop, even if...
We have an Koiki 2500 lb weld positioner withe a DC motor and drive for the rotary. The motor is a 180v 1 Hp Baldor, the drive is a Cleveland Machine Controls Pace Master MPA-04342. Although the motor is 180v (which was replaced at some point), they have the drive wired to 115v, so it only puts...
That is the motor shaft speed. The rated amps on the motor are less than on the VFD. I read that somewhere before, and double checked it. If motor speed isn't an issue, than I'll hook up this thing up and see if it works.
Side topic, since there are three pendant stations, and they will be...
Thank you sir!! I did call Wolf Automation which is whom I got the drive from years ago, and it should work, although the amp draw of the motor and amp rating on the drive are very close. The next step is wiring the momentary forward and reverse contacts since there are three locations on the...
We have a large 300 ton Southwark-Baldwin Traveling gantry straightening press, imagine a large gantry crane riding on crane rails on the floor, instead of a hoist on the I beams, it has a large hydraulic ram. The gantry itself is powered by a 5hp motor geared to jackshaft that runs to both...
Automec just does backgauge controls, not really retrofit controls for ram.
Can I ask how much the system cost?
This video has me interested in the Esa control. Looks super simple to operate.
YouTube
Also I finally found another backguage company, and retrofit company in Michigan. ZAKRON -...
Not to throw this topic off track, but what is the name of the company? I found an italian company that did retrofit controls, Esautomotion, but never got a response.
We have 3 Weldsale Acorn welding tables tables for sale, they have the 1 1/2" holes, and are in good condition, these were also cast in the USA. Located in Dayton, OH. Can load with crane or forklift. Asking $1500 ea.
Phone: 937-679-9605
I will hold my breath for 10 years. A large majority of tradesmen (machinists, toolmakers, welders,etc) are 55 or older. I was in a larger fab shop last week, and the foreman was talking about going to the races, he mentioned OVER HALF his employees were getting the 55 and over discount. I...
I know rolling is more of an art than science, but I am getting my ass kicked when rolling parts 180 degrees (or any angle really) in the middle of a panel. I figure my neutral axis length for the flat pattern, I then mark the INSIDE radius flat length on the part, then slowly crank up the back...
There is no pump, I see gantry style presses all the time, and they money they bring is almost new price. Especially for a table size over 30" wide.
We are straightening more than plate. Plates are easy to straighten, especially with a torch, but an assembled weldment doesn't move so easy...
The cylinder has two springs, attached is the link for the manual with diagram http://www.dakecorp.com/manuals/Elecdraulic%20I%20-%20905%20Series.pdf . I was mistaken on the stroke, it is actually 16", not 12.
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.