Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Largest Manufacturing Technology Community on the Web
Stay Connected:
Recent content by onecut
-
O
Sorry about delay just seen your message.Dont really understand what your asking?.Whats an...
Sorry about delay just seen your message.Dont really understand what your asking?.Whats an Artillery carriage?- onecut
- Profile post comment
-
O
Milling cutters for milling difficult materials? welded Cast iron, Al Bronze, Repairs ect.
Get yourself a Ripper Cutter its a roughing tool.That will do the type of thing your talking about.Remember if your machining weld or chilled cast iron,etc you should be on a relatively slow speed.Too fast and you will burn your tool out -
O
Willl this flycutter design work?
They are illegal in UK.Health safety that Dinky one may be ok as they were outlawed because of the issue of getting a safety guard on the larger type.Must say the larger ones had their uses- onecut
- Post #19
- Forum: CNC Machining
-
O
Setup question: drilling big holes in small discs.
You can multi load in your chuck clamp discs together with "g clamps" -
O
Help Finding
The guys are saying this for future refrence anyone asking the same question can search "SHALLOW DEPTH GAUGES"and see past answers.Its nothing personal- onecut
- Post #16
- Forum: CNC Machining
-
O
Cncmiller40
Hi,Steven surely someone who you work with could have told you,Reading a mic especially to fine tolerance is all about "feel"for best results you should be using the "ratchet"on the mic.Its not a "G,Clamp" so does not need to be overtightened-Good luck use the Ratchet- onecut
- Post #5
- Forum: CNC Machining
-
O
fun acme thread job
Wow machines that size goes with the operators bad back-Lovely work wouldnt like one of those chips down my shirt front -
O
Tips on using a vise, stock pushed up when tightening
Have the workpiece higher in the vise gripping on a 1/4ins works fine.When your milling first face square you can have it deeper if you want.But faces 3/4 which are the finished sizes should be gripped higher in the vise.Doesnt matter if parallel moves but should be down on final... -
O
Counter Sinking Questions
Your post 14 comment about the c/sk on final depth.Think its a bit like a parting tool once the tool is cutting dont stop it go to final depth.As has been suggested a pipe on your handle so you can get a steady feed to depth and WD40 WILL help.This sounds like a light weight machine and if your... -
O
Counter Sinking Questions
500revs far too fast.ItS aIways temping to run then too fast.No harm in trying a lower speed say 200 and go from there think on the machine your using slower will be faster.When you get near the depth a squirt of WD40 then go to depth suspect its lack of power.Tool must be sharp even stoning the... -
O
Problem with drilling
Think I would drill holes with a dremel with 90degree attachment that would fit in the bore of the cylinder.You need something to equally space the holes.So turn a collar to fit in bore.Lock in place with couple grub screws -
O
Bridgeport Textron 1MDI milling machine
These machines were often found barely used normally with its friend the interact next to it which everyone would prefer at the time.They would be left unused stuck in a corner most of the time with the tables without a mark on them a lot of them had the boss controls on them.The program could...- onecut
- Post #7
- Forum: CNC Machining
-
O
NEED HELP: Bridgeport VMC 460
Hi if you google what you want,You will be able to download it.- onecut
- Post #2
- Forum: CNC Machining
-
O
How can I remove a rivet head bolt?
Cut them off with disc grinder.Put new one one and heat head with torch,Dome it with small tack hammer.If you need screw driver slot in head cut slot in with dremel to stop it spinning