What's new

Recent content by Rocha

  1. R

    Mitsubishi EDM DWC110SZ software loading problems

    Any Mitsubishi service technician with experience on this problem that can provide feed back or procedures to solve parity error codes in red that appear on monitor. ?
  2. R

    Mitsubishi EDM DWC110SZ software loading problems

    I have problems to input system disk on machine no image on monitor after following normal procedure. I tried using floppy disk (3 FD) and using software on USB and emulator. Loading procedure looks like works but at the Time Machine is power off and on to load English disk or files nothing...
  3. R

    Reading / Loading Mitsubishi fx20 Disks

    I am wondering what was the solution to your system loading problems.
  4. R

    Mitsubishi DWC-110sz alarm U728 water coll.err

    system loading software issues I need your advice. Mitsubishi DEC110sz. System software download. After a problem of no edge detection , was tried to reload the software but every even if appear that system files are downloaded ,after follow normal procedures to see “English language loading...
  5. R

    Mitsubishi DWC-110sz alarm U728 water coll.err

    I need your advice. Mitsubishi DEC110sz. System software download. After a problem of no edge detection , was tried to reload the software but every even if appear that system files are downloaded ,after follow normal procedures to see “English language loading ” on monitor and boot system...
  6. R

    Mitsubishi DWC-110sz alarm U728 water coll.err

    Looking for advice on problem with system software download Need advice. Problem to download system software on Mitsubishi DWC110SZ. After downloading 2 first programs ,7.1 and 7.2 software on usb , and moving switch to system start and turning off and on after imput English language file...
  7. R

    Alarm U827 reasons on FA10S

    At start up , after several minutes loading the software, main display appear. Hitting ready button appear alarm U827 asking to input parameter 0000. Not doing nothing machine shutoff by itself. All this happen after replacement of Z driver.
  8. R

    Cincinnati Dart 750 tool changer miss alignment

    What is the way to align tool on spindle. I need to turn about 1/8” carrousel but mechanical looks is not possible. Any password to modify like in Haas Mills. ?
  9. R

    Okuma Crown V

    Looking for 4 linear bearings for X axis. Due to poor Okuma service I am asking if somebody know the commercial part number. Appears are THK bearings.
  10. R

    Mitsubishi wire EDM CX20

    STILL NO SOLUTION. REPLACED KOSB BOARD AND NOW CONTACT TURN ON AFTER WIREFEED BUTTON IS ON, ONLY 24 VDC ARE ON TERMINALS 105-106 OF POWER SUPPLY. X1-X2 NO POWER AND VO-N150 NO POWER. IN OTHER MACHINE VOLTAGE are 24vdc on 105-106, 77 on x1-x2 and 12 on vo-N150,TALKING ABOUT POWER SUPPLY
  11. R

    parameter loading

    Mazak 20B with Mazatrol 32B What was the final solution to this problem. How was possible to reinstall the parameters w/o be able to insert the reinitialization disk to turn black screen alive ?
  12. R

    Mitsubishi wire EDM CX20

    Thank you for your advice. I will try tomorrow and post the result.
  13. R

    Mitsubishi wire EDM CX20

    Any feedback.? I disconnect and connected after testing one by one the cables that goes to upper and lower heads. I play with Di water resistivity. No change. Same alarm if contact after M84 (machining) is enable.
  14. R

    Mitsubishi MV2400R - T/C In fluid error

    I have similar problem but on CX20 model. Resistívity read 2. Green . I checked 3 pin sensor and float an looks good. Di pump is On all the time. Could be a resistivity too low that water is not conductive affecting made the 3 pin level sensor ? I connected and disconnect one by one every...
  15. R

    Mitsubishi wire EDM CX20

    Problem with Contact On alarm as soon as machining is activated manually or by program What could be potential solution. ?
Top