Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Largest Manufacturing Technology Community on the Web
Stay Connected:
Recent content by SageGlad
-
RIGID TAPPING CYCLE PROBLEM Mori Seiki Mill
The M29 for some reason run the cycle with no problem, but when I erase M29 and leave just S2000 the machine alarms. Makes no sense to me though, because G84 is the tapping cycle that are supposed to run the complete cycle in that lane. Thank you for pointing to the parameters, I'll defiantly...- SageGlad
- Post #22
- Forum: CNC Machining
-
RIGID TAPPING CYCLE PROBLEM Mori Seiki Mill
Hey guys, thank you all for replying to me. I have this resolved. Turned out that the code should look a little different, the code example below just in case someone will find himself in the similar situation. Machine: DMG Mori DMC1035V Ecoline 2015, M730B Mitsubishi control with MAPPS...- SageGlad
- Post #20
- Forum: CNC Machining
-
RIGID TAPPING CYCLE PROBLEM Mori Seiki Mill
I tried with no M3, when S200 inside cycle (alarms that spindle rotation command was given during rigid tapping cycle). If I erase S200 it’s not running because there is no command for the spindle now. Doesn’t make sense..- SageGlad
- Post #13
- Forum: CNC Machining
-
RIGID TAPPING CYCLE PROBLEM Mori Seiki Mill
I’ll try it in the morning with my code. Thank you!- SageGlad
- Post #11
- Forum: CNC Machining
-
RIGID TAPPING CYCLE PROBLEM Mori Seiki Mill
How would your tapping code look like? For 16 TPI tap (for whatever tap)- SageGlad
- Post #9
- Forum: CNC Machining
-
RIGID TAPPING CYCLE PROBLEM Mori Seiki Mill
I tried to command M3 inside the cycle, outside the cycle and no change.- SageGlad
- Post #7
- Forum: CNC Machining
-
RIGID TAPPING CYCLE PROBLEM Mori Seiki Mill
Hey guys. It is Mitsubishi M780B control. The tapping cycle is G84 on these controls. It's alarming actually about spindle related something. I'm attaching the photos of the screen with the alarm and the descreption.- SageGlad
- Post #6
- Forum: CNC Machining
-
RIGID TAPPING CYCLE PROBLEM Mori Seiki Mill
Hey guys. I have a problem with the rigid tapping cycle. The machine alarms when I use the code to tap the holes. Can please someone advise what might be wrong with the code? The machine Mori Seiki DMC1035V Mill. T12 M6 S200 M3 G54 G0 A0. M8 G0 X1.14 Y0. G43 Z1.147 H12 G0 Z0.747 G98 G84 X1.14...- SageGlad
- Thread
- Replies: 21
- Forum: CNC Machining
-
Change Mitsubishi control parameters degrees per minute to inches per minute
Thank you guys, that was a G93 you all correct. inverse time feed supported by this machine, it's DMG Mori. They sent me the manual with the explanation and examples. Talking to my post guy now to make it work! Thank you again for all your help, I love this place and y'all.- SageGlad
- Post #4
- Forum: CNC Machining
-
Change Mitsubishi control parameters degrees per minute to inches per minute
Hey guys. I got Mori Seiki DMC mill, it's 4 axis machine. Anybody knows how to change parameters in Mitsubishi control for A axis? When F speed is commanded all other axes moves with the commanded speed, but A axis moves like 10 times slower or so. I assume it's something related to degrees per...- SageGlad
- Thread
- Replies: 3
- Forum: CNC Machining
-
-
Insert Chipping
I've found that every time chuck (almost all of push) closes, load meter show some pressure applied to Z axis = to the stopping tool you use. I measured in between .001"-.006" depending on setup. I'd use something else to stop it, and I always pull back from the part before homing turret for...- SageGlad
- Post #7
- Forum: CNC Machining
-
proven turning inserts for obtaining the best finish in 303 stainless?
I've never used any better inserts. They also lasts forever with right speed/feed.- SageGlad
- Post #13
- Forum: CNC Machining
-
Need Help, cannot open chuck, Machine Not ready
As VTM said, there is a breaker (contactor-breaker) for the hydraulic unit, look at the electrical ladder which should be in the book with your machine, and find this breaker number. See if it tripped off, turn it back on and see what happens when you turn the pump back on again. If it will trip...- SageGlad
- Post #4
- Forum: CNC Machining
-
Spindle bearing died during warmup on newly installed (used) machine
Obviously this is a mechanical issue, and spindle disassembly much faster then go back and forth on the forum. I'd go remove it, and all questions will be answered right away.- SageGlad
- Post #17
- Forum: CNC Machining