What's new

Recent content by spurst

  1. S

    Mori seiki sl2 h

    Thank you yea mine is a Sl2-H with a twelve station and a 10 inch chuck and could not figure out what was missing on the casting to add a tailstock,so I guess you answered it there is none. Thank you that's why there are no used Sl2 tailstock out there
  2. S

    Mori seiki sl2 h

    Can anyone tell me if they made a tailstock for a mori seike sl2-h
  3. S

    Mori Seiki SL2-H Turret problem

    Thanks for all the help, It turns out that there was one switch on the back of the turret that was bad. I finally figured out the diagnostics and found the correct bit, its was just a switch that was bad
  4. S

    Mori Seiki SL2-H Turret problem

    I don't know if it has a encoder or not I would not know if I was looking at one. But mine does have Seven switches on the back of the turret. Plus 3 on the X axis's
  5. S

    Mori Seiki SL2-H Turret problem

    Yea mine also the op manual from Mori is for a 6T controller.
  6. S

    Mori Seiki SL2-H Turret problem

    Ok Thank you, I will try to see if I can figure out which one is which The Mori instruction manual I have is the one that came with the lathe new, but someone down the road changed the controller from a 6T to a 3T Fanuc I do have the 3T connecting maintenance manual and the maintenance manual...
  7. S

    Mori Seiki SL2-H Turret problem

    I took the turret rear cover off and looked, all the wiring looks to be in good shape, its surprisingly clean, what do i need to check the switches with a volt meter, to see if they are sensing when the blocks come under them, they all seem to be spaced out about the same clearance.
  8. S

    Mori Seiki SL2-H Turret problem

    Ok thank you I will remove that cover and take a look
  9. S

    Mori Seiki SL2-H Turret problem

    That over my head I don't know how to figure out the diagnostic bits are you saying to check to see if the sensors are reacting to open-close sending voltage. I don't know where the sensors are I presume on the turret,
  10. S

    Mori Seiki SL2-H Turret problem

    Could it have messed up one of the sensors because I rotated the turret in reverse, I have not messed with the Parameters
  11. S

    Mori Seiki SL2-H Turret problem

    It just stops all operations no crashes or nothing, when it goes to home to index, Turret just rotates then stops not locked, and on random tools
  12. S

    Mori Seiki SL2-H Turret problem

    Hello I have a older Mori Seiki SL 2-H Lathe with a Fanuc 3T Model F Controls. I am having turret problems no crashes other than a broken dill bit 1/4 inch. Its a 12 station turret, What it is doing is, when it indexes it will not stop rotating, after a bout 10 revs it will stop not locked, and...
  13. S

    Drilling holes in SS on Lathe

    Thank you for your help
  14. S

    Drilling holes in SS on Lathe

    If i need a .250 and .500 hole within .0005 what size do i drill before ream, how much will a reamer take off and stay accurate. Thanks for your help
  15. S

    Drilling holes in SS on Lathe

    Yea I need the holes to less than .0005 Drilling them lucky if the hole is within .003 allways cone shape larger toward the turret. Yes i face the rod then center drill or spot drill makes no differance. I press them to a shaft force fit,
Top