What's new
What's new
By:
Advanced search…

Search results

  1. daryl bane

    Little over priced or have I disconnected on 10EE value?

    "Except for the missing lower cover." Dang, you're right. I guess I thought they had just removed it for inspection. That's a big issue.
  2. daryl bane

    Little over priced or have I disconnected on 10EE value?

    "Rode hard and put up wet" as my mother would say. But it looks complete and undamaged from the pics. Might make a good project if the price was right.
  3. daryl bane

    10EE C16J tubes

    Just a thought. When you applied power, did the CJ16's light up at all? If it is like the WIAD, you turn on the power, the tube heater elements come on. nice orange glow. Then when you push the lighted green button, you should hear a click/lock, and the tubes inside should light up a pretty...
  4. daryl bane

    Testing oxygen and other high pressure cylinders.

    Tried to post a link but didn't work. You can see it on YouTube. Welding Supply in Dallas going up 2007. Pretty impressive, I remember this.
  5. daryl bane

    10ee for $1,400 in California

    Unless I am missing something, it is not a Inch/metric. I think you are looking at the large Micro-Gaging cross feed dial ( a nice accessory), which looks like the Inch/metric one.
  6. daryl bane

    10EE C16J tubes

    Unless you're like me and just like the tubes for the "cool" factor, switching to Scissio is really the way to go. I have a set of the Scissio units for backup, but still run the tubes for fun. One thing though, my tubes (maybe not everyone else's) require a good 15mins or so to get fully...
  7. daryl bane

    Old Autocollimator Parts

    Ha, I couldn't imagine what Zeiss would charge for a single one off, if they would even do it, now maybe for 1000 pcs. they might talk to you. Actually, I don't know if this is correct, but I think...think that most of their production glass (and just about everybody else's) is now made in China.
  8. daryl bane

    Old Autocollimator Parts

    Of course, you could just run down to Oberkochen, and let Zeiss make up you a replacement. I'm sure they would be glad to help. :).
  9. daryl bane

    Old Autocollimator Parts

    Would it be possible to grind down the new larger objective to fit? I wonder if an eyeglass optical shop could do that?
  10. daryl bane

    Tail stock lock lever question

    Same here, push away to lock. My Hwacheon (Mori Seiki) is the same.
  11. daryl bane

    Retrieving items dropped in chip pan

    Here is something I got the idea from some of our overseas friends. Does work quite well keeping stuff from falling into the pan. Easy on, easy off. It's sized for most of the collet chucks, etc that I use.
  12. daryl bane

    Retrieving items dropped in chip pan

    I don't have a pic, but I found a large (like 24" long) pair of medical forceps that work great for this kinda stuff. Also good for getting parts that roll under the bench. I have also used the locking feature to roll up a wad to swab out a tube. Very handy.
  13. daryl bane

    OT What's up with all these phone calls from odd ball callers

    I used to get car warranty calls many times a day. Now not so much. Usually what happens now if I do answer, there is a pause (this is the tipoff to hang up), then the robot says, "Hello? Hello? and if I reply, it goes into its spiel. I think anytime you buy something online and they require a...
  14. daryl bane

    EE Apron thrust Bearings.

    Ok, I figure this out. If you go to "Open link in new tab" you can down load it. ...I think. Cal, maybe you can clean this up and put it in a sticky?? If this info is not already available.
  15. daryl bane

    EE Apron thrust Bearings.

    Here is a rough sketch of some bearings/numbers that I sent to Bob at General Bearings probably 20yrs ago. I was going thru my files, and I didn't know if this would be handy or even relevant now. The first two 1) &2) might not be for the Monarch(maybe Tree mill) I just don't remember.
  16. daryl bane

    City permit woes

    If I had the talent or energy to do all the work myself, I would've sure gone that route, and never involved the city, in any form or fashion. But I got a respected contractor who plays by the rules, and this is the way I have to play.
  17. daryl bane

    City permit woes

    When we were trying to figure a way to permit a 200amp panel upgrade, (which should not be a big deal) I asked my contractor, " what if I told them I might want to build alittle home woodshop in the back? " He turned white, and said, " DO NOT mention "WOOD SHOP" ever !!!! That opens a huge can...
  18. daryl bane

    10EE Taper Attachment restoration and some questions about different styles.

    If everything fits up, why not? You may have to make a new crosslide leadscrew bar, not a huge job, but that is just a hunch.
  19. daryl bane

    Tree 2UVR-C Questions

    As far as your mounting is concerned, I have mine sitting on 4 -Royal 4 1/2" dia. isolastic machine mounts, and those are sitting on 7"x7" x4" Tall paving blocks from Home Depot, as I like the machine a bit taller than whence it came. Been setup like this for 20+ years and rock steady.
  20. daryl bane

    City permit woes

    There was some speculation between me and the contractor about that. One, was that I was going to run a business in there and needed the power. I told them I wanted nothing to do with having a business( TRUE!!) or anything to do with that. Two, that I might be going to put in an inside...

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2023 Copyright Practicalmachinist.com. All Rights reserved.

Top