What's new
What's new
By:
Advanced search…

Search results

  1. 7

    FS: Kent CNC MILL & Huge Screw/Fly press

    Mill has been sold, screw press still available
  2. 7

    FS: Kent CNC MILL & Huge Screw/Fly press

    Yep, but ebay sometimes leads to in-person deals
  3. 7

    FS: Kent CNC MILL & Huge Screw/Fly press

    5% discount off the eBay price
  4. 7

    FS: Kent CNC MILL & Huge Screw/Fly press

    Links to details on my ebay listing KENT CNC MILL Kent CNC Mill | eBay SCREW PRESS Blacksmith Forging Screw Press Fly Press | eBay
  5. 7

    WTB Fadal vmc15 or similar sized cnc mill

    San Diego but willing to go to LA area as well
  6. 7

    Cincinnati Cintimill w/vertical head + huge tooling, san diego

    Need to make space and willing to sell fast for $500 Cincinnati Cintimill 205 vertical mill - tools - by owner - sale
  7. 7

    WTB Fadal vmc15 or similar sized cnc mill

    Looking for a vmc15, vmc15xt or similar In the SoCal area
  8. 7

    G76 for internal threading?

    I have a 96 Hwacheon with Fanuc OT and mostly use a USB in tape mode but wanted to accomplish some internal threading using the G76 command. For internal threading is it simply change X(u) to the negative -Diameter? FORMAT G76 P(m) (r) (a) Q(∆dmin) R(d) G76 X(u) Z(w) R(i) P(k) Q(∆d) F(f) ex)...
  9. 7

    FS; Clausing Lathe and Cincinnati Mill

    Location: 92065 Clausing 6913 lathe with 5C collet closer, wedge tool tool post, steady rest, 4 jaw chuck, 3 jaw chuck, live center. Crossfeed screw was repaired but should be replaced. Has some bed wear. Newcross feed nut was installed, reeves drive sleeve was re-graphite epoxy coated and...
  10. 7

    Cincinnati Toolmaster 1D; are my dogs fried?

    Took a cut today and the dogs disengaged so I tore the head apart. The culprit seems to be the ball detent groove on the main shaft is worn allowing the shaft to sit lower than it should. My plan is to drill a new hole in the sleeve to hold the ball and spring so that it contacts the shaft along...
  11. 7

    First press brake; are my dies wrong?

    I couldnt get less than around 95 degrees. I checked the upper and lower dies with a machinist square and they both appear to be 90 degrees. Should I try to find more acute dies or is it worthwhile to machine the dies I have?
  12. 7

    First press brake; are my dies wrong?

    I picked up a chicago 135 press brake and was test bending some 18 ga stainless with these dies and it did not get to 90 no matter the stroke adjustment so I am guessing my dies are incorrect. I pulled them from a pile from the seller and evaporusted them before testing them out.
  13. 7

    Need help with Fanuc 0T-C offset settings

    Thanks for the input guys. I found that the wear offsets were huge 3+ inches and that was throwing everything way off. I set them all to zero, ran the program and made my first CNC lathe parts without crashing or breaking anything. I set up a USB DNC system from Highland CNC because I will be...
  14. 7

    Need help with Fanuc 0T-C offset settings

    The X axis exceeds the travel in the negative direction in the program below. I am new to CNC turning & Fanuc controllers and need some input from the brains here Recently acquired 1996 Hwacheon Hi Eco 10 w/Fanuc 0T-C (only has G50; can't get to a G54 page and old programs in memory use G50)...
  15. 7

    Mori crossfeed screw question

    I had the dial removed to show the jam nuts. I repeated the tightening and each time ran the cross slide back and forth a few time and after a few of these, it seemed to finally stay tight. Perhaps the bearings needed to be run in for a bit.
  16. 7

    Mori crossfeed screw question

    Looking at the 2 nuts that retain the outer thrust bearing, it looks like I am missing a washer or something to keep these nuts in place. They quickly loosen after moving the crossfeed screw back and forth a few times. I cant seem to locate a diagram so was wondering if anyone knows what I am...
  17. 7

    Looking for suggestions on smaller footprint cnc lathe

    I'm considering a small cnc lathe (footprint of around 60" x 115") to use for making my own parts (small runs of simple parts ranging from 2.5" 4140PH to 1" 1018 and all less than 12" lengths). From what I have come across in the used market, a hwacheon hi eco 10 seems to be a good choice but I...
  18. 7

    Van Norman 1RQ with dividing head, DRO, tooling in So Cal

    $1200 takes it with the tooling
  19. 7

    Van Norman 1RQ with dividing head, DRO, tooling in So Cal

    Open to reasonable offers van norman 1RQ (has quill with 4 inches of travel) vertical horizontal mill with tooling dividing head arbor support. Has a power knee, integrated coolant system, power feed on the X, power feed on the Z, 3HP head is very capable of hogging. Great stout mill, many nmtb...
  20. 7

    Considering buying a 1971 Monarch EE 10 x 30

    here is a pic

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2023 Copyright Practicalmachinist.com. All Rights reserved.

Top