What's new
What's new
By:
Advanced search…

Search results

  1. H

    LNS Service Parameters

    I will try that one. 2534 is one of them, but not the one I need
  2. H

    LNS Service Parameters

    2534 is one, and that gets you into certain areas, but there is also another that will get you more menu options. I will check with them Monday morning. I was trying to get one over the weekend if someone knew.
  3. H

    LNS Service Parameters

    I have a 2013 LNS quick six and need to access the service parameters. Does anyone know the password?
  4. H

    DMG Mori NLX2500SY Post Processor for Solidcam

    I'm in a pinch and need a post processor for a DMG Mori NLX2500SY with sub spindle. SolidCAM is currently 4-6 weeks out and I need to start ASAP on a part order. I'm not sure why they don't have a basic off-the-shelf post for this machine they can provide. [email protected] anyone that...
  5. H

    DMG Mori NLX2500SY Post Processor

    I'm in a pinch and need a post processor for a DMG Mori NLX2500SY with sub spindle. SolidCAM is currently 4-6 weeks out and I need to start ASAP on a part order. I'm not sure why they don't have a basic off-the-shelf post for this machine they can provide. [email protected] anyone that...
  6. H

    Hardinge Superslant with alarm 2008: X axis break is on

    X axis brake Did this machine get fixed? I am having a similar issue
  7. H

    Bar Feed Macro Program

    I don’t recall seeing any 9000 programs in the directory, Or are they located somewhere else? Sent from my iPhone using Tapatalk
  8. H

    Bar Feed Macro Program

    Gotcha. Will touch base in the morning Sent from my iPhone using Tapatalk
  9. H

    Bar Feed Macro Program

    ox....I will check in the morning and let you know. What I can tell You is I have been through every nook and cranny on the LNS and set up all the information needed. Set the end of bar position with the teach mode, And also the top cut position. Also set up all the information on the part...
  10. H

    Bar Feed Macro Program

    Ox....what Counter are you referring to? Parts counter on the Mori? Yes it response to Chuck open and Chuck closed as you described Sent from my iPhone using Tapatalk
  11. H

    Bar Feed Macro Program

    Bill, The M70 is a Mori M-code on this machine. It specifically signals the bar feed to load another bar. I have tried it through MDI and it works fine...loads a new bar into topcut position. I checked all of the I/O links on the LNS PLC and communication functions are good to go between the...
  12. H

    Bar Feed Macro Program

    OX....I will finish putting the code together in the morning for a trial run and let you know how it turns out. Had to tend to another machine for most of the afternoon...blake
  13. H

    Bar Feed Macro Program

    I do believe so...will keep you posted Sent from my iPhone using Tapatalk
  14. H

    Bar Feed Macro Program

    OX....greatly appreciate your help. Trying to get production on this part running today so it can run throughout the night.
  15. H

    Bar Feed Macro Program

    OX....This LNS has the options to fully retract the pusher and let the lathe do the feeding as I am with the subspindle. It follows the lathe progress by counting how many chuck openings M11 (that equals parts made). As you can see in my my main program I take care of the bar pull with the sub...
  16. H

    Bar Feed Macro Program

    OX. Actually the way you suggested would be better, I just wasn't sure how to implement that method since I am running 7/8" hex stock and need to implement an M19 spindle orientate to line up the collet hex with the bar upon every bar load. I have a 98 LNS quick servo and would prefer to have...
  17. H

    18i-T G28 on axis with absolute address only

    I just came across this same scenario on my Mori ZL-150S. I had to forget about setting a G54 B Zero at the face of the part. I had to jog the face of the collet on the sub spindle and record that position to write into my program. Naturally G28 B0. first move was to go to the part zero first...
  18. H

    Bar Feed Macro Program

    Bill, M70 calls the bar feed to load another bar. Attached are the programs for head 1 and 2.
  19. H

    Bar Feed Macro Program

    Hello all... I recently installed a LNS quick servo bar feed on my Mori ZL-150S. I am knew to bar feed jobs and macro programming as well. I know there are hundreds of posts about bar feed macros on here, but I can't seem to find one that fits my scenario. Plus understanding the Macros is a...
  20. H

    G05/G08 on Fanuc OM-C

    Hello all, Has anyone used G05/G08 on a Fanuc OM-C Control? Just looking to improve surface finish on a simple 3D surface. Thanks in advance

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2023 Copyright Practicalmachinist.com. All Rights reserved.

Top