Largest Manufacturing Technology Community on the Web
Stay Connected:
Search results
-
J
Ultimax Work Offsets
I believe you are limited to 54-59, if not please let me know how you worked around it!..- Jtlambert
- Post #2
- Forum: Hurco and Milltronics
-
J
Centurion 6 DNC is outsmarting me, any help appreciated
Hi All, We have a partner 5 w. Cent6 controls. We usually send over files via RS232 using Realterm on the computer. It takes a long time but it generally works fine. I'm trying to run a part now that is too large to download onto the machine and I'd like to use DNC. I followed the manual I...- Jtlambert
- Thread
- Replies: 0
- Forum: Hurco and Milltronics
-
J
Help please! Poor Monarch CM in desperate need of maintenance.
Update/next problem.. So we got the clutch together on the old Monarch, I'm not convinced it's exactly right but it's pretty close and the machine runs. The guys have been using it life is good. That is until this weekend when something went wrong in the headstock. In the middle of use the...- Jtlambert
- Post #9
- Forum: Monarch Lathes
-
J
Hard tapping mystery (G88)
Working on a Centurion 6 controlled Partner 5 machining center, we have rigid tapping available and it seems to work fine but it always adds a 10 second dwell at the bottom of the hole and another 10 second dwell at the top of the hole. Thread down, 10 seconds, thread out, 10 seconds, move to...- Jtlambert
- Thread
- Replies: 1
- Forum: Hurco and Milltronics
-
J
Miltronics Servo Mystery, help wanted
Update.. Well after replacing the ballscrew, motor&cable, all bearings and having my service guy in here for 2 days the machine is all back up and running. all axes are holding 0.0001. I think that machfab had it on the nose. There was a bunch of carbon dust in the motor but I didn't find...- Jtlambert
- Post #8
- Forum: Hurco and Milltronics
-
J
Miltronics Servo Mystery, help wanted
Hi All, long shot here but I wanted to see if anyone had seen anything as weird as what I'm experiencing. My local rep and I are both stumped. We have an older Miltronics partner 5 and for the most part it gets new parts when it needs them, tech comes in on an annual to check and calibrate the...- Jtlambert
- Thread
- Replies: 7
- Forum: Hurco and Milltronics
-
J
Help please! Poor Monarch CM in desperate need of maintenance.
Thanks! Machine ran today and made chips. I did notice that the clutch hub was a bit warm after running, is that normal?- Jtlambert
- Post #7
- Forum: Monarch Lathes
-
J
Help please! Poor Monarch CM in desperate need of maintenance.
Gentlemen, Thanks for the help. This weekend I was able to get the clutch assembly back together and it's working great. I do have a couple remaining questions though that I'm wondering if anyone can help me with. 1. There are two oil ports on the top of the leadscrew gearbox, (circled in...- Jtlambert
- Post #5
- Forum: Monarch Lathes
-
J
Help please! Poor Monarch CM in desperate need of maintenance.
Rabler, Thanks for the reply, I'll take a stab at some springs. I did order the manual but it was pretty generic and didn't help in that area. All the other parts are ordered so we should be putting it back together next week and I'll report back with what else is broken.. Cheers!- Jtlambert
- Post #3
- Forum: Monarch Lathes
-
J
Help please! Poor Monarch CM in desperate need of maintenance.
Hi all, first time posting here. I recently purchased a Monarch 22CM. 12,000lbs of beautiful iron I just couldn't say no to. Unfortunately it looks like maintenance wasn't big on the previous owners list of things to do and the bearings that the drive pully ride on evidently didn't get grease...- Jtlambert
- Thread
- Replies: 9
- Forum: Monarch Lathes