What's new
What's new
By:
Advanced search…

Search results

  1. R

    Cincinnati Milacron Avenger 200MS Acramatic 850SX Not powering up operator control

    Mud, I'll see about contacting Mike Eckhart. I appreciate the lead.
  2. R

    Cincinnati Milacron Avenger 200MS Acramatic 850SX Not powering up operator control

    I'm not sure if I'm looking at the right "Yahoo Groups" This is a the link I was on for a bit looking for. Yahoo! Groups There is a note that states: "Announcement: End of Yahoo Groups We’re shutting down the Yahoo Groups website on December 15, 2020 and members will no longer be able to...
  3. R

    Cincinnati Milacron Avenger 200MS Acramatic 850SX Not powering up operator control

    I haven't called Siemens. I talked to FIVES about 2 weeks ago on a machine I picked up to see if I could get it running or use it for parts. Factory Support "FIVES" (from what I've heard from others) let go the good support people on the older machines at the start of COVID. The person I was...
  4. R

    Cincinnati Milacron Avenger 200MS Acramatic 850SX Not powering up operator control

    Good to know....Thanks for the insight. Rosie
  5. R

    Cincinnati Milacron Avenger 200MS Acramatic 850SX Not powering up operator control

    Short and simple I think something wasn't making a good connection on the “DC POWER DISTRIBUTION SUBASSEMLY” I'm referencing page 4-2-3 of the Control Reference Manual Publication No. 7-000-0738CR May 1992. If you look at page 3-2-5 you'll see the Power supply part number 3-424-2082A. Below...
  6. R

    Cincinnati Milacron Avenger 200MS Acramatic 850SX Not powering up operator control

    Cincinnati Milacron Avenger 200MS 1994 with Acramatic 850SX Not powering up operator contol First and foremost: Thank you for all input in advance. Normally I have called up the factory, however since COVID started all the knowledgeable people are no longer there and these machines are “No...
  7. R

    Acramatic 850sx not communicating with front pane PC.

    I do not know if it is helpful or not, however one of mine on it's first start up in my shop 14 years ago took about an hour to get past the "host control initializing". It had sat for quite a while before I got it. Now if it sits for a few days or a week it does take more than a couple minutes...
  8. R

    Need Help Cincinnati Milicron

    Ok....I just dealt with the 15312 Alarm again. I am rushed for time....so if anything doesn't make sense ....please ask. Please follow the above information that I gave with the sequence. That sequence is directly from the factory. This is the advanced and what is needed to know for the scenario...
  9. R

    HELP!!! I think the spindle bearings on my cincinnati turning center are bad.

    Just a follow up for future reference or searches. As a reminder I have a lot of spare parts for Cincinnati Milacron Avenger 200MT's and MS's. I also wanted to avoid pulling the headstock off of this machine like the Plague. The headstock alignment is very good on this machine. Before this...
  10. R

    HELP!!! I think the spindle bearings on my cincinnati turning center are bad.

    gregormarwick I have a spindle that I bought for the resolver. I did pull the bearings from that one.....just to see how it would go. I did this a few months back. I didn't have a very good set up, however I was able to do it. I'll read your other thread....and thank you with the words of...
  11. R

    HELP!!! I think the spindle bearings on my cincinnati turning center are bad.

    david n I don't run the machine alot....and I do feel as if the machine has served me well .....all things considered. As to where I've been......life has gotten busy.....business, kids, reality don't give a bunch of free time.
  12. R

    HELP!!! I think the spindle bearings on my cincinnati turning center are bad.

    vmipackman, Your idea of re-greasing the bearings is the route I'm thinking now. I'm going to do a trial run of pulling the spindle cartridge from a parts machine first to see how it goes. I ran the machine in question today for a couple hours. I have a cheap stethascope to listen to the...
  13. R

    HELP!!! I think the spindle bearings on my cincinnati turning center are bad.

    Well it's 14 years later. I have quite a bit more knowledge of these machines....and quite a few parts now. As a reminder it is a: Cincinnati Milacron Avenger 200MT There is no lubrication system. They're open bearings and factory greased. Spindle Bearings: FAFNIR 2MM9124WI x 5 of them I...
  14. R

    Cincinnati Avenger 250T Acramatic 850SX alarms initialization (manual required)

    When you shut this machine down.....do not use the big red emergency button. I avoid the "Big Red Button" like the plague on this type of machine. You press the control off button when you're ready to shut down.....leave the Big Red alone. The machine takes 5 or more seconds to remember the...
  15. R

    Need Help Cincinnati Milicron

    I have not dealt with your Hydraulics Issue yet. However I have similar issues with buttons. I have a 1994 200MS that when it sits for a while.....some of the buttons don't work worth a sh!t. If I massage them a bit they'll start to work. Don't push overly hard....simply push and...
  16. R

    Need Help Cincinnati Milicron

    "ALERT NUMBER 15312 NON CYC ALERT SL LUBE FL" I have a 200MT that I put the larger actuator in....to make a 2-1/2" machine....and I have a 200MS. I'm fairly sure I've had this same alarm in the past. There is a solenoid valve that supplies the lubrication system. The oil supply is from the...
  17. R

    FS: Dial Bore Gauges

    Steve the Cylinder gage is yours. I'll send a PM.
  18. R

    FS: Dial Bore Gauges

    Jacques I will send you a private message with shipping information. The Mitutoyo is yours. Thank you
  19. R

    Shop Cleanout: Lyndex Chuck Wrenches, Fly Cutter, Parting Tool, Refractometer

    Glad to hear. The first Refractometer I purchased was from ebay and shipped from Canada. The nice guy put about two layers of shrink wrap under the shipping label for protection. Needless to say it was junk. Thank you for the reply.
  20. R

    FS: Dial Bore Gauges

    If nobody is willing to pay full price by Monday I'll accept the $200.

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2023 Copyright Practicalmachinist.com. All Rights reserved.

Top