What's new

Search results

  1. C

    Exceed Live Tool RPM Limit

    Mori Seiki SL-25 MC, Control 15 TF. I exceed the live tool rpm limit which caused alarm "1458: milling holder join time up". I talked to a tech at Mori and he thinks the issue is proximity sensor 55. I looked over the parts list and drawing and there are no sensors in the list. Can someone...
  2. C

    Need Help: Mori Seiki SL 25 Alarm 1458

    I accidentally programmed the rpm too high for the milling tool, now it will start and stop like 5 times then alarmed out.
  3. C

    Mori Seiki SL 25 Spindle Motor

    I'm trying to figure out which one of these is the correct motor for the Mori SL 25. I had a tech from Fanuc at the shop today and he couldn't figure out why both motors have the same part number with different ratings.
  4. C

    Fanuc Spindle Motor Bearing

    I have a Fanuc spindle motor (A06B-0731-B900-#0900) that needs a new bearing, I called Fanuc to get a part # for the bearing but they don't do component-level parts. A local shop quoted me $1500 in labor to replace the bearing, I would like to find out the cost of the bearing beforehand. I...
  5. C

    Mori Seiki SL25 Alarm 12 on Spindle Servo Drive

    The 0A00 has the same fan, actually it look exactly like this one. The specs are a little different.
  6. C

    Mori Seiki SL25 Alarm 12 on Spindle Servo Drive

    Yes, 0A00 is the original motor.
  7. C

    Mori Seiki SL25 Alarm 12 on Spindle Servo Drive

    Does anyone know if these two motors are exchangeable??
  8. C

    Mori Seiki SL25 Alarm 12 on Spindle Servo Drive

    I remove the cover from the spindle motor where the wires are connected, I could smell that some got burnt so I went ahead and start the removal process. Now I'm trying to decide if I should repair it or take a chance on a used motor. TIE send me a preliminary quote for $3300 until further...
  9. C

    Mori Seiki SL25 Alarm 12 on Spindle Servo Drive

    I purchase this machine 4 years ago and every year since, I have repaired the spindle drive for alarm 12. I have a second SL25 that run flawlessly for the past 4 years, so now I have come to the conclusion that something is causing the drive to go bad. Where do I start looking? Do I pull the...
  10. C

    Cnc broaching

    Rotary broach won't work.
  11. C

    Cnc broaching

    Can you pm me your shop information, I'll send over the drawing for a quote.
  12. C

    Cnc broaching

    Anyone here notices any premature wear and tear on their lathe from long term broaching? I have 200 parts that need a 1.375" 6 Splines, 3" deep. I did a dry run and it's going to be about 30 mins to broach each part. That's over 100 hours of hard start and stop on the ball screw. The machine...
  13. C

    Mori Seiki SL with a Yasnac LX3?

    Hey guys, I hope someone here can help me with some Parameters Settings To get to this screen you will need to change the Rotary Switch on the upper left of the master board to 4, then turn on the control while pressing the shift key. You should get the following screen. Now you will press...
  14. C

    Anyone familiar with AMGC Ram Error?

    Mori Seiki SL15 with Yasnac LX3 Control. First, the machine would lose power to the control and other times it would alarm out with the following alarms. 362: PG Error Z 361: PG Error X 332: Fuse (Z) 310: Fuse (X) 310: Servo Off I removed the PS and replaced a bad capacitor, after reinstalling...
  15. C

    Fanuc 15T KEEP RELAY to disable tailstock

    There is a handle on the tailstock that need to be manually engage to the turret, to move the tailstock back and fort. I wrote a program to lineup the turret with the handle of the tailstock, then I would manually engage. After engaging the handle to the turret, the program will not run...
  16. C

    Fanuc 15T KEEP RELAY to disable tailstock

    Machine is a 1980 Mori Seiki SL 25B I'm looking for the keep relay to disable the tailstock engagement so I can move it backward and forward in the program. The tailstock need to be manually engage and disengage. At the moment, once the tailstock is engaged (manual handle the couple tailstock...
  17. C

    No power to servo drives.

    My Mori Seiki SL 15 with a Yasnac LX3 control just stop in the middle of running a part. I will attached a picture of the alarms. It seem like I lost power to my Z & X servo drives. I replaced the power supply but the problem remains.
  18. C

    Machine is not responding to feedrate programmed

    Program Edit Key Parameter. Anyone here know which parameter disable the program edit key?
  19. C

    Machine is not responding to feedrate programmed

    Yes dry run was activated, it wasn't on the control so it took me some time to figure out where it was.
  20. C

    Machine is not responding to feedrate programmed

    I didn't try to run any threads, I'm sure it will not run any threads since its not using the the feedrate in the program. I try run a part off tool at .0001 feed and it was cutting at 5 IPM,where the feedrate ovr knob was.
Back
Top