What's new

Search results

  1. M

    Hurco Autobend 7 Y-axis manual jog limit

    Hey all, Recently bought a press brake with a Hurco AB7 back gauge and ram control. I am having trouble getting the Y axis (bend depth) manual jog to any further than .5" up or beyond the limit switch when in active mode, it just stops. No errors, basically just goes to 4.491 and stops, limit...
  2. M

    Ran my belt sander on 3 Phase while wired for single

    Hi DSK, yes, both the breaker and the overload were tripped.
  3. M

    Ran my belt sander on 3 Phase while wired for single

    Thanks Richard. Called Jet, they said it's probably the motor. Im not getting any burnt smell from the motor, but I am from the contractor and the overload. I may try to replace those.
  4. M

    Ran my belt sander on 3 Phase while wired for single

    Correction, it does not have a single phase option, it has 2, 3 phase voltage options, 230 and 460, it was wired for 230 and was plugged into 460 (480 actually)
  5. M

    Ran my belt sander on 3 Phase while wired for single

    Hi All, SO I was a bit anxious in getting my belt sander fired up and toasted something. It is a Jet belt sander/grinder with ability to run single or 3 phase, it comes wired for single and I plugged it into a 3 phase 480v outlet. It ran for a bit then stopped. When I plug it into single phase...
  6. M

    Promecam RG-20, Iroquois 48/40 Press Brake Value & Opinion

    Hi All, I'm in search of a smaller CNC press brake (cycle control and job memory, CNC back gauge is not necessary yet), mostly for 14ga mild sheet metal production. I've been watching this press for a while and am going to go check it out soon. Does anyone know a realistic value of this...
  7. M

    Iroquios pressbrake.

    Thank you for your input Toolbert, that may be the ideal direction for me at this point in my business. Are you familiar with this brand, Promecam? 20 Ton x 04' Promecam Model RG 20 CNC Hydraulic Press Brake | eBay They have quite a few models I may go check out. Seems really difficult...
  8. M

    Iroquios pressbrake.

    Thanks for the input guys. Pardon my ignorance as I'm just trying to figure out what will be best for my needs and budget. I will mostly be bending 14ga mild around 3 feet maximum currently. The sharpest bend being around 70º and a few more bends at 90º and roughly 170º etc per part. The 70º...
  9. M

    Iroquios pressbrake.

    In the same boat with interest in the 72/100 press brake from Iroquois. Did you move forward with one of their products? Thank you,
  10. M

    WTB- 6-8 Foot Press Brake

    In the same boat with interest in the 72/100 press brake from Iroquois. Did you move forward with one of their products? Thank you,
  11. M

    CNC Plasma Table X & Y issues - Circle

    I had already made sure they were tight, same result, thanks.
  12. M

    CNC Plasma Table X & Y issues - Circle

    Hi All, I'm having issues with my axis running properly or smooth. I usually run circles for testing how well it's running. It's a pretty simple setup that I recently upgraded, control box is running a Gecko g540 with 570oz Nema 23s, single motor X axis, using a pulley and belt (XL037) system...
  13. M

    Hydraulic press cylinder will not retract

    Thanks for the suggestions guys. Yes, I completely disassembled the cylinder. I had already bought a rebuild kit for it from blackhawkparts.com, but when I got in there, I was surprised to find rubber seals that looked brand new (whereas the rebuild kit had the "rope" type packing and a hard...
  14. M

    Hydraulic press cylinder will not retract

    I recently updated my old Manley 60 ton press pump to an electric hydraulic unit, it previously had a manual Enerpac P-25 hand pump which worked great but am trying to run it more efficiently and faster with the electric. The pump works great, the problem is, it will retract any longer, it...
  15. M

    Manley Hydraulic press parts

    Manley 190 60 ton rebuild Hey guys, I have a 60 ton Manley 190 I am rebuilding with the Blackhawk kit. Any pointers or suggestions you can offer would be appreciated. Thank you
  16. M

    Plasma Trigger On/Off Gecko G540

    Thanks, I have tried port 1, pin 1, I also have relays hooked up like the attached diagram.
  17. M

    Plasma Trigger On/Off Gecko G540

    Hi All, I recently upgraded my plasma table's controller. The previous one already had connections on the box for my plasma trigger and was wired internally. My new control box houses a Gecko G540 board and I am having difficulties getting my plasma trigger to activate through Mach3. I have...
  18. M

    Belt Sander for removing welds?

    Thank you Evan, I appreciate that!
  19. M

    Belt Sander for removing welds?

    For sure Chip, I will definitely bend as many corners as possible as soon as I get my new finger brake. Thanks for the input!
Top