What's new

Search results

  1. W

    Tool nose compensation

    I solved the problem by positioning the tool at the middle of the groove in Z. I dont know if that is the correct way to do it, but it works. And yes, it will actually cut the same as shown in the simulation. Thanks Bill for all your help. I test run the part, looks like the 6mm button insert...
  2. W

    Tool nose compensation

    Hi Bill, your code is working fine! No errors. Just one thing - the tool escapes to home position right thru the shoulder the shortest path. What do i do wrong here?
  3. W

    Tool nose compensation

    Bill, I will past the programm into my cycle tomorrow and run it. I will get back with the results. I owe you a lot of thanks for all your help! You are saving my day!
  4. W

    Tool nose compensation

    I have attached a file with the dimentions, i will look into your next post also, thanks a lot. Just to be clear, i started profiling at the top edge of the part and ending on second top edge, as there is not enough clearance. I have another tool doing the first rad on the beginning, and the...
  5. W

    Tool nose compensation

    The interesting thing is if I run the program without tool nose compensation, there is no issue. So the points must be programmed right, i am just missing something about the tool nose compensation, i guess. I have a dxf drawing, where i get all the points from
  6. W

    Tool nose compensation

    Thanks, Bill, for pointing out to the X coordinate. In the start X i dounded it to 3 decimals and in the last to 4. But even i put in the X2.894, same error occurs. Something with the tool nose comp. And yes, somehow i didn see there was two G40s
  7. W

    Tool nose compensation

    I am trying your method, working out actually good, the only problem i have in the canned cycle once the roughing tool is done it rapids out the shortest path from the bottom across the shoulder of the part. How can i force it first go up to safe position to leave the part?
  8. W

    Tool nose compensation

    Thanks Bill, no it shows alarm 452 code 10 (End point of the arc command after calculation of LAP, tool nose radius compensation, or tool offset is offset from the programmed arc more then the specified tolerance) and the programm stops at the red line: N200 G95 G97 T010101 M3 S1400 M8 G0 X3.5...
  9. W

    Tool nose compensation

    here is the code snippet roughing tool: N200 G95 G97 T010101 M3 S1400 M8 G0 X3.5 Z1.12 G85 NAT2 D.1 F.02 U.000 W.000 G84 NAT2 G81 G0 X2.894 Z.500 G1 Z1 F.01 G42 Z.8843 G3 X2.8055 Z.7937 I-.1157 K0.0000 G1 X2.6102 Z.7165 G2 X2.4000 Z.5000 I+.1705 K-.2165 G41 G2 X2.6102 Z.2835 I+.2756 K0 G1...
  10. W

    Tool nose compensation

    I have a DXF file where i get all my intersection points, so i did write the code for that profile. But now if i need to recreate the profile lets say 6mm (for my rough tool) and 4mm for finishing, thats where i see it a little complicated. Maybe I am thinking wrong...
  11. W

    Tool nose compensation

    Would be more helpful, if you could explain how to do that... I mean the programming part, the shoes i can figure out myself:)
  12. W

    Tool nose compensation

    I would be too complicated to handwrite the code for that profile
  13. W

    Tool nose compensation

    Yes I mean direction 8. Attached is the part. I am not at the shop now, will post my code snippet later. If i programm without G41/42, it simulates well.
  14. W

    Tool nose compensation

    Hello, need some help! I am programming a V-shape groove on the OD of a part with some radii. Usually i am not using G41/42 for simple parts. This one is a bit more complicated. I am confused. I am programming by hand, controll is Okuma OSP5020L. Tool is a full rad with Walter RCMT120400 Insert...
  15. W

    Okuma Spindle Problem

    Hello, I have a Okuma LR15-M/3T machine with 5000L-G control. I got it from an auction, so I dont know the history. Machine starts up ok, but the spindle will not move. Sometimes it is working ok, but all of a suddon the spindle does not response. It can be during cut or sometinems just even...
  16. W

    max rev over on okuma live tooling

    I just got it going with G50
  17. W

    max rev over on okuma live tooling

    Hi, i just got a used OKUMA LR15-M/3T with osp5000L-G control from an auction and try to get it going. I have similar okumas at my shop, so I am familiar with them. I use the same program that I used on the other machine, but this machine throws an Alarm 339 "max rev order m axis" as soon as it...
  18. W

    BL-D drive disable

    Hello, i have a Okuma LR15-2M machine with BL-D drives. I am not using live tooling, but still have a couple of BL-D Drives to controll it, and sometime due to the age they are failing and giving an alarm, even if i dont use them or dont need them. Is there a way to just disable them? Thanks
  19. W

    Okuma LR 15-2M Turret Issue

    By hand, correctly sayind would be manual mode. Clamp/unclamp works fine, clamp confirmation LED on the TCC is on
  20. W

    Okuma LR 15-2M Turret Issue

    Yes, i can move the turret by hand, i can move the turret from the back of the Turret Control Card with dip switches in Maintanance Mode.
Back
Top