What's new

Search results

  1. L

    Looking for C16J tubes

    Hey all I have a monarch 10ee and I'm looking for a couple C16J to get the MG drive back up and running. I'm located in North Central Illinois near Rockford if anyone could help me out that would me much appreciated Andrew
  2. L

    New to me 68 10ee

    Hello all that had helped me last week. She ran great on Saturday when I was into work. It's Monday now and I cannot get the spindle to turn nothing is different then when I left Saturday please help
  3. L

    10ee help

    Had the maching running over the weekend got to work this afternoon and I cannot get it to run. 2.2v@ the c16j tube Small tube lights up with power on. 256v across 1-3 @ PC
  4. L

    New to me 68 10ee

    Thank you all for the help getting this beauty up and tooling again. Was on phone with monarch this morning and the machine was wired for 440vac fixed that swapped everything to 230v and she fired right on up
  5. L

    New to me 68 10ee

    Some pictures
  6. L

    New to me 68 10ee

    yeah I didn't think it was good when I first noticed it, the little tube in the middle is getting up to about 80f and the right tube up to 180f while the left is room temp. ill have to pick this trouble shooting up again in the morning. thank you for all your help labeeman. Andrew
  7. L

    New to me 68 10ee

    OKay I have 2.2vac to 2.6vac coming from the transformers to both tubes left and right
  8. L

    New to me 68 10ee

    after disconnecting red leads and putting the L1 and L3 wires that were disconnected back into their proper terminals I not have 220/240v ac across L1-L3 on the terminal strip in the tube area. Now only the right tube is heating this time it got much hotter then before.
  9. L

    New to me 68 10ee

    The three orange wires coming into the power disconnect are coming from a 240v 3ph shutoff switch on the wall. my question is why the prev owner ran the red wires from the small transformer mounted to the outside of the machine to the electronics terminal strip shown in the photo, should those...
  10. L

    New to me 68 10ee

    Okay there were a couple wires labeled L1 and L3 in the power contact area then go to the panel with the tubes, they are not connect to any thing and show continuity. should I connect these wires to their respectively labeled terminal on both strips? This is how the machine arrived into my care
  11. L

    New to me 68 10ee

    the red leads in the photo came from the little transformer in the back and that is how I recived the machine. there are two wires in the tube area labled L1 and L3 with wirenuts caping them off, these two wires are connected to nothing in the power contactor area under the bed. are these the...
  12. L

    New to me 68 10ee

    I measured from across all the contacts on the tube that warms up and the smaller tube I got nothing ac or dv for voltage. measured voltage form L1 to L3 on the termal strip in the photo I got 120 vac dose this mean that the transformer on the back of the headstock mounted externally is wired...
  13. L

    New to me 68 10ee

    I do not physically have the manual( I have a pdf one on my phone) and have contacted monarch directly and have accurate wiring schematics
  14. L

    New to me 68 10ee

    yes it is the 10x 30 model and I hope I get this thing going today.
  15. L

    New to me 68 10ee

    The transformer taps on the large transformer are a good place to start. Steve you are talking about the large transformer under the bed behind the read access panel
  16. L

    New to me 68 10ee

    I checked voltage and it measures 0.0 VDC across f-2(+),18(-) control on depressed I checked voltage from s1(-), 51(+) also 0.0 Vdc control on depressed the control light comes on green and then turns off shortly after the left thyratron (c16j) is cold the right c16j tube is heating properly as...
  17. L

    New to me 68 10ee

    Sorry for doubles I am on my phone, navigation is not the best We have 240 3 phase here in a few ur shop and I can get the machine to power on but the PC will not interlock ND stay on. Previous owner has rewired some things and I would like to confirm that the transformers are wired properly for...
  18. L

    Monarch Serial Numbers

    Missed some info, machine has taper attachment, came with tailstock. Not really sure what we got with this machine but I know it's more then we need where inwork
  19. L

    Hello Cal, I have been looking for info on monarch lathes and trying to get power to the one I...

    Hello Cal, I have been looking for info on monarch lathes and trying to get power to the one I have recently aquired. There was definitely some shoddy workmanship that went into the wiring and I would like to sort it all out without any damage. The matchine is as follows Mod Monarch 10EE...
  20. L

    New to me 68 10ee

    Having some issue getting this lathe to power on. Pervious owner said he had it running at one point however I opened up the panels and found quite a bit of wiring changes I have access to 220/240 3 phase but the previous owner did not and I believe there was mention of it running on single...
Back
Top