What's new

Search results

  1. G

    016 alarm - amplifier not equipped

    Electrician came by. It is the power supply. Thank you for the help. This one is a bit expensive.
  2. G

    016 alarm - amplifier not equipped

    Hello. One of my Mazak SQT 15's has an alarm code of 016 that says " Amplifier Not Equipped" Can anyone help me out with this one at all. Thank you to all of the Mazak Guru's for all of the problems that you help everyone solve. If anyone has had this issue and knows what I need to do I...
  3. G

    Breaker trip alarm help on 1992 sqt - 15m

    Hello. Thanks again. The Electrician showed up and he opened the back doors and turned the breaker on and immediately knew what was wrong. I guess there is a 2.5 amp power supply / controller for some things on the machine that was bad. I guess these machines are notorious for these things going...
  4. G

    Breaker trip alarm help on 1992 sqt - 15m

    I am not sure on the air to air heat exchanger. I do have a reputable electrical machine repair guy coming today. I was just looking for anything that may be obvious. Thanks for all the help and suggestions.
  5. G

    Breaker trip alarm help on 1992 sqt - 15m

    When I turn the breaker on I can here the fans and stuff turn on. The control comes on and says (201 BREAKER TRIP) It prevents the hydraulics from coming on so the machine can't be moved or anything as well. I will check behind the panel you are talking about and see if I can find out...
  6. G

    Breaker trip alarm help on 1992 sqt - 15m

    Hello. I need some help. I have a 1992 SQT - 15M that just gave me a breaker trip alarm and I checked the main power breaker and reset it. I also shut the power off at the electrical control panel and reset it as well. This did not clear it up. I tried to flip any breakers I could find behind...
  7. G

    Sanyo Denki Servo Motor help needed

    Hello. Can anyone out there help me with some information on a Proprietary only servo motor. Maybe one of the maintenance or parts guru can help me out. I acquired a brand new sanyo denki servo motor from a closing machine shop auction. It was with parts from the maintenance department. The...
  8. G

    Mazak SQT - 15M Leaking Coolant Behind the Turrett

    So then there would be no need to pull the turrett off then? Sounds good. Thank you very much.
  9. G

    Mazak SQT - 15M Leaking Coolant Behind the Turrett

    Hello. I have a question and need some help. I have a SQT -15 M that lost coolant pressure and started leaking coolant behind the turrett. I did pull the hose off from the pump to the turret and turned the coolant on and ran it into a bucket. The pressure was very good from the pump. If anyone...
  10. G

    Realign tailstock on a 1990 Mazak QT-18

    I know how to program the machine using the tailstock. I just need to find the adjustment bolts. The machine came to me in the condition it is in. I can only assume that someone at the previous owners shop must have bumped the tailstock. I was told they used the tailstock all the time, however...
  11. G

    Realign tailstock on a 1990 Mazak QT-18

    Hello again, I got all of the 4 bolts loose that mount the tailstck rails to the cross slide but I can't seem to find the adjustment bolts that you are talking about. Maybe a pic will help me out if you could. If you want to send to my e-mail it is [email protected] Thank you.
  12. G

    Realign tailstock on a 1990 Mazak QT-18

    Hello. Can anyone explain to me how to realign the tailstock on the 1990 Mazak QT-18. When I purchased the machine and got it to the shop. I went to run a job using the tailstock and noticed it pulled the parts way off center. There for I had to put in a large taper line to run the parts to...
  13. G

    Quick Turn 15 with T2 Control

    Hello. Can anyone help. My buddy picked up a Quick Turn 15 with T2 control. The problem is if you try to do a regular type 1 grooving process. It will get half of the groove roughed out and then try to run at an angle all the way down to "X" zero no matter what the finish diameter is programmed...
  14. G

    Straight shank tension compression tap holder

    CAPTDAVE. Could you please e-mail me some pics of the holders that you have available too. Thank you.
  15. G

    Straight shank tension compression tap holder

    I'm just looking to tap on center with the tapping holder. Dead turning holder. Live holder wouldn't need to be compression, retention. I have a line on one on e-bay. Thank you. I am also looking for some I.D. threading bars.
  16. G

    Mazatrol T Plus Programming Question

    By the way yes you can mount a backwards facing turning tool. Say you would still need the spindle turning to the "right" direction you would describe the tool as a "left handed tool" with a "right" spindle direction. Remember though that the starting "z" would be past the length of your part...
  17. G

    Mazatrol T Plus Programming Question

    Hello. You can do this with a groove out process or with a turning process using the groove tool as a turning tool. I have made several rings for my wife and myself. To deburr the back side with a groove process you would use a groove process similar to cutting off. Use your last known final "X"...
  18. G

    Straight shank tension compression tap holder

    Hello. Can anyone help me out? I am looking for a Tension compression tap holder for sale. Please contact me with pics and pricing please. Thank you. I want to use this in my 1998 Mazak Quick Turn 200 and my 1989 Mazak Quick Turn 15
Back
Top