What's new

Search results

  1. mcbassin

    Thermal cutout / fuse replacement for old Hardinge Lathe

    SQUARE D Thermal Unit, 0.53 to 0.63 Full Load Amps, For Use With Square D NEMA Motor Starters 00, 0, 1 - 1H598'|'B0.71 - Grainger I think this is very close Amp rating but a little different design.
  2. mcbassin

    Thermal cutout / fuse replacement for old Hardinge Lathe

    I put the the green jumper in to confirm that it would work without the fuseable link. What supply house do you recommend? Grainger? Allied...? Mouser? Yes I find it odd but the wiring diagram is from 1963... It's antiquated for sure...
  3. mcbassin

    Thermal cutout / fuse replacement for old Hardinge Lathe

    Thanks Tom, When I think of a relay, I think of a contact type of device. I’m not electrical expert at all, obviously.... Are these heaters available still? I thought that this technology was antiquated. That was the reason I started this thread to fin a suitable replacement of modern circuit...
  4. mcbassin

    Thermal cutout / fuse replacement for old Hardinge Lathe

    I think the size of the pictures are reduced when loaded on here.
  5. mcbassin

    Thermal cutout / fuse replacement for old Hardinge Lathe

    I loaded that pic from my phone. Try this one
  6. mcbassin

    Thermal cutout / fuse replacement for old Hardinge Lathe

    I isolated the lower voltage problem to this thermal cutout. It has perfect voltage on the incoming side but low voltage coming out. Am I missing something? The problem appears to be the fuse. I suspect it was damaged but not completely blown when I had the wiring polarity backwards when I...
  7. mcbassin

    Thermal cutout / fuse replacement for old Hardinge Lathe

    Larry, Thank you for the response, This box (pictured) is obviously different than mine. I will take pics of my actual box. The devices I want to replace are some sort of overload protection. They are located this same area in my box. I think they might be a slow blow fuseable link? Anyway, On...
  8. mcbassin

    Thermal cutout / fuse replacement for old Hardinge Lathe

    Does anyone know where to find a suitable replacement for these antique fuse/ cutout devices? I borrowed the picture below for reference.
  9. mcbassin

    Ez trak run -time error m6104 problem

    I have a similar issue going on with my machine. Jon can you offer any suggestions?
  10. mcbassin

    FeatureCam 2016 legacy version DVD? Anyone have one laying around Help!

    Thank you for your help. I was able to install this version. I get the error about the part file being saved from newer version but it seems to work on the few files I opened.
  11. mcbassin

    FeatureCam 2016 legacy version DVD? Anyone have one laying around Help!

    That would be great. You can PM me the link. I won’t be able to download until Monday but thank you.
  12. mcbassin

    FeatureCam 2016 legacy version DVD? Anyone have one laying around Help!

    I recently upgraded my computer and lost my old version (2016 v2 22.4.1.16 specifically) I have installed 2016 from the Autodesk site but it will not run with my PAF file. So I'm looking to find a basic 2016 DVD. I'm willing to pay for shipping to me and back if you will let me borrow it. I own...
  13. mcbassin

    Hardinge HC spindle variable speed won't change speed troubleshooting info

    Thank you for the response. I was able to disassemble the variable assembly last night. I think I may have found the problem. I believe the motor is shorted in the windings. The wire leads for the motor were very brittle. The insulation flaked off when I touched it basically. I tried to repair...
  14. mcbassin

    Hardinge HC spindle variable speed won't change speed troubleshooting info

    I want to pull the electric motor out to inspect the internal wires. This machine is probably a late 70s early 80s? I'm worried the wiring is causing the issue. I snagged this photo online. It is what my variable speed box looks like.
  15. mcbassin

    Hardinge HC spindle variable speed won't change speed troubleshooting info

    Thank you for the reply. I checked the micro switches inside the terminal box. The cam never made it to the roller so I don't think it's over travel. Also, the rotation seems to be fine on the spindle. I can check that this evening. I did notice while I had the cover off the wires look very old...
  16. mcbassin

    Hardinge HC spindle variable speed won't change speed troubleshooting info

    The first day I got my Hardinge the variable speed worked to go to a slower speed but stuck there and it has been stuck since ( a long time) I have tried trouble shooting it but don't have a clue about electrical stuff. I can hear a relay kicking when I try to lower or speed up the motor. It's...
  17. mcbassin

    Carbide endmills 1/4" and 3/8"

    Thanks for offering up a good deal on these end mills. They should work perfect for my garage machine shop. should we pay you before hearing back via email?
  18. mcbassin

    Carbide endmills 1/4" and 3/8"

    I haven't heard anything yet
Top