What's new

Search results

  1. D

    DMG DMU50evo spindle oil-air lubrication settings

    Hello, thank you for the help, there is 3 tubes from the block and one with just air. I can see 3 tubes end up in the bottom of the spindle base and one in the upper section of the spindle.
  2. D

    Replacement for CL46 oil for MAHO MH600C

    I had the same problem for my machine, it states CLP46 or CL46 but when i googled the recommended oils i found out that they were ordinary hydraulic oils.
  3. D

    DMG DMU50evo spindle oil-air lubrication settings

    Hello, i need advice. What is the right pressure of air in the air-oil lubrication for the spindle and the extra air for the sealing of the spindle. Also in the base of the spindle where the oil-air tubes end up there is a hole that spits oil an air when i start the spindle, is it possible the...
  4. D

    Swapping Heidenhain DDC2 drive controllers to test - Simodrive 611

    the Philips 4022 229 3011 (in out module in the controller) has a similar pot, i thing this is the way to tell the machine what cart is what.
  5. D

    Swapping Heidenhain DDC2 drive controllers to test - Simodrive 611

    When i had made a swap in the DDC2 drivers the axis were wrong, i am not sure but i thing it has something to do with the blue pot. Regards John
  6. D

    Philips, Grundig, Millplus Information Collaboration

    Ihave send you email with my hard drive image it is V4.00 MillPlus from my DMU50evo
  7. D

    DMG DMU 50 Evolution machine constants

    This is how the have made the pipes in the newer versions
  8. D

    DMG DMU 50 Evolution machine constants

    In mine the oil radiator was leaking from the pressure. change the piping so the oil goes first to the exchanger and then to the pump so the heat exchanger wont see hi pressures. the exit from the heat exchanger has a small pipe so all the air goes out first and then the oil. the pump cant push...
  9. D

    DMG DMU 50 Evolution machine constants

    Hi, sorry for the late reply, the fan must blow air up thru the radiators. they turn counterclockwise when you look them from below.
  10. D

    Philips, Grundig, Millplus Information Collaboration

    Hello, i have send you a link to download the image of hard drive with MillPlus V400 from my DMU50evo. You need Acronis true image to make the hard disc.
  11. D

    Contest for the most insane member (They will be a Maho owner)

    Hi i have a dmu50 evo 2000, model in my machine the oil for the 4-5 th axis gets suck from the reservoir to the bottom of the casting to the pump-motor and then goes to the radiator and then to the filter and back to the 4-5 axis where it lubricates everything. the radiator can't stand the...
  12. D

    Philips, Grundig, Millplus Information Collaboration

    If you make a change in any other machine constant it keeps the change?
  13. D

    Philips, Grundig, Millplus Information Collaboration

    Hi, this is the pc in my dmu50evo i thing you have the same
  14. D

    Contest for the most insane member (They will be a Maho owner)

    Hi, can you post some pictures from the spindle internals. The rotor of the spindle is moving lilt bit down when the hydraulics push the drawbar to relish the tool. I wonder if the bearings take all the force from the tool change or the rotor is resting on the stator during tool change. You can...
  15. D

    Philips, Grundig, Millplus Information Collaboration

    It will probably be a wrong parameter.
  16. D

    Philips, Grundig, Millplus Information Collaboration

    Error 252 https://www.*******.com/forums/deckel-maho-aciera-abene-mills/373478-deckel-maho-80u-1999-millplus-e252-error.html
  17. D

    Philips, Grundig, Millplus Information Collaboration

    Hello, it will be interesting to see the procedure, can you send me the file. Regards John
Top