Search results

There’s only a couple of things it could be. The turret is operated by an air motor. Make sure your air pressure is good and very dry. These things can get temperamental if any water is in the air. You could also check the turret index position encoder. I believe there is a procedure in the...

Playing around today with the parts catcher on my Hardinge CHNC-1 and found an interesting problem. When I key in M26 in the over store screen it extends the parts catcher, key in M25 and it retracts without any issues. Then I add the M26 code into my program and it extends for about 5 seconds...

Looking to buy a chip conveyor for my 1998 Mazak QT-20. Let me know if you have any old iron you want to part with. Thank you!

Looking to purchase a chip conveyor for my 1998 Mazak QT-20. Let me know if you’ve got a parts machine and want to make some cash. Thanks!

This was a fairly easy fix for anyone experiencing the same issue. Hit the Parameter key on your control. Hit the Machine soft key under the monitor. Navigate to the A9 parameter. Record the Z-1 value (mine was 3750). Change this parameter to 999999. Power down the machine to reset the control...

Hello, I recently purchased a Mazak QT20 lathe with a T Plus control. Everything worked fine (minus quill retract) when I inspected it prior to purchase. Machine was rigged professionally and transported to my shop but the previous owner did not install any kind of shipping brackets prior to...

Feel free to reach out if anyone needs help with this in the future. I don't get on here often but message me if you have a question.

I was finally able to solve this issue after a chat with an applications engineer at Hardinge this morning. There wasn't a lot of hope after our first conversation but he was able to dig up some old parameter and cable pinout sheets that he had from a previous issue. Ultimately I was missing a...

1200 baud, even parity, two stop bits

I tried it out this morning and same data format error. I've reached out to Hardinge to see if they can assist...fingers crossed.

Thanks for the reply. I tried this and still could not get anything to go. Just as a note I've also tried punching back an existing program with no luck as well.

Hello and thank you in advance for the collective knowledge of this group. I own a Hardinge CHNC 1 with a Siemens 810T control. I am attempting to DNC a program to the control and I am getting the following error, "32 ORD14 Data format error (RS232)". I rechecked my cable pinout and everything...

It seems that my air compressor can’t keep up with the volume of air required which I knew would likely be an issue. I plan on making an investment in a new unit soon I just need to decide if I want to listen to a piston compressor or spend more money and go with a screw. Every time the pressure...

Update...if you don’t have sufficient air to your machine then it won’t clear the alarms. Face palm 🤦*♂️

Hi Guys, I’ve done some digging around and can’t seem to find any posts on successfully clearing a “6000 EMERGENCY STOP” error on a Siemens 810 controlled CHNC. I just got this lathe powered up, fluids topped off and air run to the machine. Upon initial power up I attempted to reference the...

PM me with a photo please. Do you know what year it is?

Mmmmmmm maple bacon anything sounds delicious! It definitely needs a little love. It fires up and runs smooth. I need to figure out how the auto feed stuff works, but for now I won't worry about it. Moving it around will be a challenge but that's why I own a pallet jack! Thank you everyone for...

The deal is done! The guy offered me the saw for $100 Dunkin' Donuts gift card and I am going to help him sell some other equipment that was included in a building/business he recently purchased. He even offered to deliver the Jaespa for free!

The one I have now is the smaller version and was rode hard before I purchased it. I’m open to all options right now. I’m going to look at a Jaespa saw tonight. I think it’s a little large for my shop now but it could be a saw I grow into.

This is tempting because 1 it’s local and 2 it’s cheap. Does anyone have experience with these saws? I know it’s not a Kysor but will it perform and last.