What's new

Search results

  1. B

    OT Generator Frequency Meter

    Take a look at a "Kill A Watt" meter. They are about $25. They are very handy for looking a smaller electrical loads. http://www.google.com/search?q=kill+a+watt Some of the Fluke meters require a minimum current before you can get a frequency reading.
  2. B

    Items for sale

    I would like the Parlec Collet Chuck if still available.
  3. B

    OT: Goggle search of Practical Machinist

    I wanted to pass along a google tool that I find very helpful, the "site:" command. I like the search provided by the site for somethings, like user names. There are times when google does a better job of tracking down information that has already been discussed. I did google for a previous...
  4. B

    Kearney Trecker Deal alert.

    The mill has been relisted as http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=330002722547 It now has a little more tooling and an interesting attachment.
  5. B

    K&T 2H Problem

    Update: I am not sure what changed the lockup problem but I had changed much, looked under the rapid traverse clutch cover, moved the sump pump around and pulled the pulleys to confirm the motor wasn't the problem. When I put a pulley back on, the lockup was gone. Put the other pulley back on...
  6. B

    Index Mill - Opinions?

    The 2H should weigh about 3500 pounds. Wade: Good find on the mills.
  7. B

    K&T 2H Problem

    I just double checked and the problem occurs in the direction of the arrow on the sheave. This is also the direction of rotation under power.
  8. B

    K&T 2H Problem

    I have seen the spindle rotate until the blockage is hit, this was under power at the time. This happened when I backed the motor up by hand and then engaged the power. I'll give the clutch a try.
  9. B

    K&T 2H Problem

    When I "spin the motor" I have the right side door open and just manually turn the motor. I also put a tool holder in the spindle to get a hold on and spin the motor. The coolant pump that is in there has a separate power supply. I will look for signs of an old pump drive. I'm not sure what...
  10. B

    K&T 2H Problem

    I have a new to me K&T #2 HL Universal Mill, serial number 15-5147. I have a couple of questions that might be related. I have a K series parts manual which doesn't seem close enough, so some of the terms might wrong. I just ordered a parts and operator manual for the H series. Sorry for the...
  11. B

    OT : Does homemade biodiesel fuel actually work?

    Here is a good forum to start with if you want to make your own. Look for the appleseed processor http://forums.biodieselnow.com/ You want to not skip steps and pay attention to the quality of the used vegetable oil that you pick up. I have ran B100 ( 100% Biodiesel ) in a 94 Dodge truck for...
  12. B

    WTB Shaper

    Thanks, I didn't find any with a search for shaper at their site. I'll try giving them a call in the morning.
  13. B

    WTB Shaper

    I would like to buy a medium sized shaper in repairable or better condition. I am going to be in between Colorado and Michigan this weekend and the beginning of next week with a gooseneck trailer. I will have about 7000 pounds of capacity left. So this rules out the really big ones. If you...
  14. B

    Horizontal Mill advise wanted

    Dave, Thanks for checking. That is good to know.
  15. B

    Horizontal Mill advise wanted

    Well thanks for the information. I did put in a bid. We'll see how it goes. I wouldn't want to get anything too new. I have a Harrison 13" lathe from 1973. I forget the age of a Cincinnati no. 2 tool and cutter grinder, I think it was the 50's. The Reid surface grinder would be in the same...
  16. B

    Horizontal Mill advise wanted

    So, you don't think the directional feed popping out would be that big of an issue on mill listed on e-bay?
  17. B

    Horizontal Mill advise wanted

    I am looking for an older horizontal mill with a vertical head attachment. This is for non-production work. I am new to metalworking. While I am a new member to the board, I have appreciated the knowledge of this forum for quite awhile. My question is, What models to look for and to avoid? I...
  18. B

    Reid 2B Surface Grinder

    I haven't seen any references to manuals online or hard copy. I also have a Reid 2B that I am working on ( starters were toasted ). The y feed mechanism seems to work and I would be happy to send you some snapshots if that would help. This forum has been such a help to me, it was nice to see...
Top