What's new

Search results

  1. jcollings

    14" Lodge & shipley ball stop missing

    Missing the ball stop ball Part #1396 Any one that knows the size of it please let me know. This is part of the 2 turns in and hits a hard stop, same as out when tumb screw is tightened, for threading.
  2. jcollings

    L&S American L1 spindle nose

    I have a Lodge and shipley 14 Model A. 1943, It does have the American L1 spindle. Anyone that knows this machine could confirm the internal taper size. OEM had a adapter that fit spindle and fit the MT 4 Same as tailstock.
  3. jcollings

    L&S 14" Literature says made by monarch

    I just purchased this lodge and shipley 14" lathe, the documents I find say that it was made by monarch ?? can anybody chime in and confirm whereas I know nothing of this machine Thank you, Sent from my SM-G975U using Tapatalk
  4. jcollings

    follower rest identification

    Can anyone ID this follower rest. Thank you Sent from my SM-G975U using Tapatalk
  5. jcollings

    Clausing 4 jaw chuck

    New old stock clausing 4 jaw Chuck for 10" 4900 series lathe. 1-3/4 ×8 tpi $190 plus shipping. Thanks Sent from my SM-G975U using Tapatalk
  6. jcollings

    Dumore tool post grinder

    have a series 44 model number 8071 , Looking for the bearing number for spindle shaft. If someone has disassembled and knows that specific number Would like to verify. Thank you Sent from my SM-G975U using Tapatalk
  7. jcollings

    Furnas J103223 switch

    Recently purchased this switch on on a site used. It does not look right as to the contacts for a neutral position forward and reverse, the contacts do not make a good connection by the looks shown. any input on this or people confirming would be greatly appreciated. pictures attached. Sent...
  8. jcollings

    WTB Dog drive plate

    Post in wrong area earlier Looking for 6" Dia 1-3/4 ×8 tpi Dog drive face plate Thanks Sent from my SM-G975U using Tapatalk
  9. jcollings

    Dog drive plate WTB

    Looking for 6" Dia 1-3/4 ×8 tpi Dog drive face plate Please send PM Thanks JC Sent from my SM-G975U using Tapatalk
  10. jcollings

    Clausing 10" 4912 parts WTB

    Looking for parts for this lathe, specifically compound, bottom half. Anything else might be interested. Thanks JC Sent from my SM-G975U using Tapatalk
  11. jcollings

    Biax tooling

    Looking for recommendations or private people for scrapers hand/or power for sale. Yes I'm aware of the commercial vendors and ebay . Asking more so as to this site and knowledge. Thank you Sent from my SM-G975U using Tapatalk
  12. jcollings

    Clearance on 9" SB drive wheel

    Looking for the clearance measurement on the cone pulley motor drive assembly, bench model. there is a collar that locks the shaft in place. Next to the drive assembly cone pulley After that collar is locked there is a small amount of play that the shaft can slide back-and-forth which gives a...
  13. jcollings

    Road trip

    Today I am going to see a 9-inch Southbend 4 ft bed. I contacted the person last night about making the trip, also two months ago talked to him, so this morning I contact him him and confirm that I'm on my way. 70 miles after I pull off the expressway I get a text from him saying oh there's...
  14. jcollings

    9" SB with VFD

    Well after very few responses on OEM motor setup for a SB 9x3 back drive machine has anyone configured this with a VFD? I've heard good things about the Teco L510-101-H1-U drive. Any suggestions or experience? Thank you Sent from my SAMSUNG-SGH-I317 using Tapatalk
  15. jcollings

    New member

    Trying to get information on a 1952 9-inch half horsepower lathe motor. mounting Dimensions spread of bolt pattern. Thank you Sent from my SAMSUNG-SGH-I317 using Tapatalk
Top