What's new

Search results

  1. D

    Barfeeder issues - Mazak Space Save 2000

    It is not a servo, works off of pneumatic. We push against a hard stop. During a normal push we position the stop and then open the chuck, then slowly move Z to final stop point then close the chuck. This part works with no problems so far.
  2. D

    Barfeeder issues - Mazak Space Save 2000

    Hello everyone, I have a Mazak SQT-10MS (T-Plus control) with a space save 2000 bar feeder which came with the mazak (both used). M06 Will open the chuck and extend the pusher/stock. M07 Will close the chuck and retract the pusher. At the end of bar, when it sees the M69 it will jump to sub...
  3. D

    Live tool max spindle speed parameter Fusion 640T, SQT250MY

    We have a SQT250MY with a fusion 640T control. The live tooling should go to 4500 rpm but it maxes out at 2000 rpm. Called mazak service a few times and they said I need to change some parameters but was unsure which ones and would check and get back to me. Was wondering if any one knows which...
  4. D

    T+ Control - Registering New Tools

    Thanks Gobo. I knew it had to be simple. My problem was I did not realize you had to hit the far right button to get more options. Now it seams so simple. Thanks again.
  5. D

    T+ Control - Registering New Tools

    Hello everyone, we have a SQT-18MS with a T+ control that we are just getting up and running. My question is, how do I add more tools? Mainly I want to add 2B for working on the sub spindle. I can edit the existing tools to change them but am at a loss on how to add more. Attached is a pic of...
  6. D

    hutson vibratory finisher tumbler massachusetts $1350

    PM and e-mail sent. Thanks, Dean
  7. D

    Main spindle and live tooling at same time SQT250MY -640T

    Is there anyway to run the main spindle and the live tool at the same time on a Mazak SQT250MY with a 640T control? I want to run a sanding wheel/brush in the live tool holder along the turning as the main spindle rotates. Not sure if it's possible to spin both at the same time, and if it is...
  8. D

    Bandsaw clamp....last call

    Ray, mine showed up Saturday. A pair at that! Thanks very much. They will go in my box with the special tools. :) Dean Webb
  9. D

    Bandsaw clamp....last call

    I would like one also Ray. Thanks! PM sent Dbwebb
  10. D

    "32mm system" dowel drilling Q's (wood)

    I always liked to set the dowels on the face side first, with the panel laying flat on the bench (hard surface). This way you can feel and see if they are all the way in and the hard surface keeps from creating a bulge on the other face. Also, if you press/pound them in too fast you can...
  11. D

    "32mm system" dowel drilling Q's (wood)

    We use the ketchup bottles. To me they were faster and easier than the Lamelloel tip. Was hard to control the amount of glue and more of mess than it was worth. The squeeze bottles are cheap and easy to have more than one person assembling. We go 5/8 deep in the face and 1" plus on the edge...
  12. D

    "32mm system" dowel drilling Q's (wood)

    We use 8mm dowels for all our 3/4" material. The bits are brad point with a 10mm shank with a flat on it. 8mm fluted dowels are fairly cheap. Baer Supply is one source for both dowels and bits. We use standard yellow glue (tite bond) and just use a simple squeeze bottle with a cap that goes...
  13. D

    Local onsite help VMC-410B

    Hey guys, We have a 2005 Mazak VMC-410B with Mazatrol 640M Nexus control and a 2002 SQT 250MY with a Mazatrol 640T PC-Fusion-CNC control. I am looking for someone who is relatively close to us that would be willing to come over and help us get started with both machines. Our shop is located...
Top