What's new

Search results

  1. F

    Lathe Series 61 Parts List

    I have a manual in good to poor condition listed as a Series Parts list. Missing cover. First page starts withe page 5 and end with page 80. Page 5/6 and 79/80 are detached but very readable. I assume it's for a Monarch Series 61 lathe. Free to someone that can use it that's willing to pay exact...
  2. F

    Way cover for Gorton MasterMill

    My desire is to protect the cross feed screw. Ways are in perfect condition and it look like it has way wipers. The mill has square ways not dovetail. Center raised section is 5"wide X 12" long but does not come in contact with the carriage above similar to that of a ToolMaster mill. My concern...
  3. F

    Way cover for Gorton MasterMill

    I have 12" rated cross travel, might be a little more but can't check it at this time due to the machines location. However I did move the cross as far back as it will go and have 12" of ways exposed. What is the total collapsed length of the Gortite cover on your BP. I have longer travel but...
  4. F

    Way cover for Gorton MasterMill

    I picked-up a really nice Gorton MasterMill from HGR some time ago. As with just about everything from HGR there were a few issues.Down feed variable speed potentiometer was bad, replaced and feed works. Spindle counterbalance spring was broken, made another it too now works.Machine is in...
  5. F

    Chinese DRO quality

    I really don't want a DRO with all the bells and whistles I will never use. Too many have the face of the DRO with so many buttons it makes it hard to use. My Anilam Wizard does have quite a few features but not buttons. For example if you want to find the center edge find one side, 0 then the...
  6. F

    Chinese DRO quality

    Seem odd they don't make them. There are a lot of machines that don't need the bells and whistles like surface grinders and Horz. mills. It's possible they are called something else, maybe I should add surface grinder to my search, actually I would mind having a simple readout on my grinder.
  7. F

    Chinese DRO quality

    I give one a try. I did make an offer on one, they countered but it said it's out of stock. Thought maybe the counteroffer was to me for the last one but the seller has yet to reply to my question if it was available. But it does have a lot of features I don't want as I mentioned in previous...
  8. F

    Chinese DRO quality

    I want a simple DRO with no bells and whistles. I do have a Anilam Wizard on my Jig Borer that came with the machine but never use the functions other than the direct reading X and Y. Often I get needed dimensions from Auto CAD or calculate polar coordinates and mostly do one ofs. I simply...
  9. F

    Chinese DRO quality

    I have 2 Sony, Anilam and a Sargon that have been working very good, no problem except with last power outage. Sony's still work great, Anilam needed setting change and it's working now too. Sargon is dead but I do have an Anilam Miniwizard I can use. Might give the Chinese DRO a try.
  10. F

    Chinese DRO quality

    I've noticed DROs made in China in ebay cheap! Would be nice to put one one my Horizontal Mill though the dials have served me well. DRO would be easier to see and easy to zero. Most of the computers are made in China as well as cell phones. I have a cheap Shinese digital caliper in my home desk...
  11. F

    Taper cutting tool for Moore Jig Borer tool holder storage

    Is the a Taper cutting device to cut the approx. angle of a Moore tool holder? I purchased 3 Susta brand tool storage holders from HGR some time ago. I have attached the frame near my Moore #3 Jig Borers. I have 2 frames of 11 holders each full of holders. However a number of the hard Red...
  12. F

    Analam Wizard help

    Thanks again Martin. Rereading the manual I see the code I should have used is1000101 in X and 0000101 in Y. Not sure why the last 3 digits being 0 worked unless I have .00005 scales. First digit in X is for turn on in inch or metric. I'll try re-entering the code and see what happens. I check...
  13. F

    Analam Wizard help

    Thanks to Carbide Tip that e-mailed me the manual. I did push #8 ten times and got into settings. X was 1000111, Y and Z were 0000111. I changed X to 0000111 and nothing changed. Changed X and Y to 0000000, being Z is not used I did nothing to it. Works!! now when moving the dial .1000" DRO...
  14. F

    Darex M-5 info needed

    When you finally get the chuck apart be careful not to mix-up the fingers. They must go back in the same location they were removed from. I have them color coded with fingernail polish. The grinder works best with Diamond or CBN Borazon wheels
  15. F

    Anilam A166 Info

    I have been to that site but can't seem to find the DRO I have.
  16. F

    Anilam A166 Info

    In searching the web I found a link to this forum dated quite a while ago. I replied but don't see any reference up-date. I need someone with a manual for the A166 Wizard or MiniZizard. Due to very recent power interruption my Wizard is now reading 5X the actual movement. I need to know how to...
  17. F

    Analam Wizard help

    I will try entering F20 but looking at the photo I see no F key on my unit. Maybe that Dot to the right of 0 is the F key. I'll see what it does later to day. I'll also look to see if I have inch or metric scales if the numbers are still on the scales. Thanks!!! Did check and found fuse in...
  18. F

    Analam Wizard help

    Here is a photo of the DRO I have and the model. Hard to see but it's A166-3000000 Yes the display is exact. I recall when I received the machine how accurate the dials were compared to the DRO, they matched in reading! Haven't used the dials since the DRO is easier. But now in checking the DRO...
  19. F

    Analam Wizard help

    My fuse diagnosis was for the other DRO on the Toolmaster mill. It's off but outlet is powered and will not turn on, completely dead. Work light plugged into same outlet turns on. Didn't do more checking as I was interested in the Analam unit. I did remove power from the Analam, flipped power...
  20. F

    Analam Wizard help

    Not sure if this is the correct forum but I have a problem with my Analam Wizard DRO. Up to Thursday night the readout was working fine as it is set-up to do. It's on my Moore #3 Jig bore. Reads in .0001 increments as it would be needed on a Jig Borer. Friday while sitting at my computer at home...
Top