What's new

Search results

  1. Doozer

    Hendey T and G part needed - Coil

    I think Pete Shapeaholic or someone else might have an old drive they took out. I am looking for the 230v DC solenoid coil (or 2) from the Reliance drive control. It has a coil on the Forward and one on the Reverse contactors. They are Arrow Hart brand contactors. I looked on the internet...
  2. Doozer

    Shaping a Helix on a Planer

    Found this on youtube. --Doozer
  3. Doozer

    Pratt & Whitney 2A comes to Doozer's Shop

    I'm going to leave this right here. --Doozer
  4. Doozer

    FS- 1927 SouthBend 9" Junior Lathe - Origional Paint- Charlotte NC

    Was my Uncle's lathe, was owned by his father, bought new for automotive shop. I have the SB overhead clutch drive pulleys. Have chucks and toolbits and change gears, lots of old stuff that was with the lathe for 75 years. Bed is NOT scratched. Probably worn some, but you can't tell. No wear...
  5. Doozer

    FS- 1927 SouthBend 9" Junior Lathe - Origional Paint- Charlotte NC

    Was my Uncle's lathe, was owned by his father, bought new for automotive shop. I have the SB overhead clutch drive pulleys. Have chucks and toolbits and change gears, lots of old stuff that was with the lathe for 75 years. Bed is NOT scratched. Probably worn some, but you can't tell. No wear...
  6. Doozer

    FS- 1933 Van Norman Piston Grinder - Charlotte NC

    I am never going to use this thing. I bought another cylindrical grinder instead. $500. Come get it. [email protected] -Doozer
  7. Doozer

    Hendey T&G Metric threading

    Some are confused by "gear feed in thousands" in that table. 100 tpi is 10 thousands feed. What am I missing? I had to think about this. It does seem confusing. The OUTPUT of the Norton box is either to a Leadscrew (and then to the half nuts) or to the Feedrod (and then to the feed clutch...
  8. Doozer

    FS- 1927 SouthBend 9" Junior Lathe - Origional Paint- Charlotte NC

    Was my Uncle's lathe, was owned by his father, bought new for automotive shop. I have the SB overhead clutch drive pulleys. Have chucks and toolbits and change gears, lots of old stuff that was with the lathe for 75 years. Bed is NOT scratched. Probably worn some, but you can't tell. No wear...
  9. Doozer

    FS- 1933 Van Norman Piston Grinder - Charlotte NC

    I am never going to use this thing. I bought another cylindrical grinder instead. $700. Come get it. [email protected] -Doozer
  10. Doozer

    Facing Head for HBM Help Identify Maker

    At a recent auction I bought a facing head, hoping to fit it to my G&L 25T. It was an online auction, and the head was on a pallet with some lathe faceplates. I could not tell the size, but it looked like a smaller head, not those 36" ones you see on Ebay all the time. Well I was the...
  11. Doozer

    Hardinge brothers oil stoves key fob

    Hardinge Brothers Oil Burners Advertising Key Chain | eBay Hardinge brothers oil stoves key fob. Thought some of you might be interested in this Franklin Hardinge artifact. --Doozer
  12. Doozer

    STRONG magnetic V-Blocks, any good brands?

    Was looking for some import magnetic V blocks. Reason I am posting this, is that number one, I have seen/used Brown&Sharpe magnetic V blocks, magnets, and mag chucks, and all the B&S magnets I have used seem very weak. Anyone agree or disagree with this? So secondly, I would like to buy a set...
  13. Doozer

    Add a Metric QC box to the HLV-H seperate from the origional

    For us lowly HLV and HLV-H owners that do not have the later HLV-H-EM lathes, I was thinking about metric gearing again. I have come to find, that the change gears on the HLV-H lathe do not compound through the QC box like all other lathes, rather they are a separate entity that does not go...
  14. Doozer

    HLV-H lathes ruined by coolant. How many suffered this fate?

    It seems many HLV-H lathes I have seen have been rusted and ruined by coolant. How many suffered this fate? I bought a HLV-H for $4000 that is pretty good, other than the cross slide dovetails are pitted and scored from black rust. The way lube lines were also clogged up nasty. The coolant...
  15. Doozer

    Old End Mills with the Morse taper tang shank, Any old fellows know??

    What are those old End Mills with the Morse taper tang shank for? You have all seen them. Without a drawbar would those end mills fall out under use? Unless used only for counter-boring bolt heads, which I could see. But were they meant to side mill? Perhaps some of the older members here...
  16. Doozer

    Granite Surface Plate: How do I drill holes to mount inserts or thru holes?

    I have no experience in this. On a Granite Surface Plate, how do I drill holes to mount inserts or otherwise through holes? I have drilled plenty of holes in concrete for anchors, but I don't think I want to use my Hilti TE72 on a granite plate. I would think one would use a carbide drill bit...
  17. Doozer

    THE vise from the grandfather

    Welcome. Nice Vise. If you have some time, you might want to look here... The VISES of Garage Journal - The Garage Journal Board --Doozer
  18. Doozer

    Idea... 2 speed motor for RPC

    This is sort of a mental exercise to spur some creative thinking... I have a 4/8hp, 900/1800 rpm motor, 230v only. If one were to use it for an RPC, (and start via pony or potential relay and caps), and powered the low speed windings, and took power off the high speed windings, you would get 30...
  19. Doozer

    Covel 512H cylindrical grinder

    I just bought a Covel 512H cylindrical grinder. S/N is 200, pre-Clausing I believe. Everything works on it, just needs a good clean. I am going to take the table off and scrub it in the parts washer and scrub the rest of the machine with Simple green. Anyone have a manual for this machine? Any...
  20. Doozer

    Where to buy a #4 Morse w/tang to ER40 adapter

    http://www.ebay.com/itm/E-MTA4-ER40-082-Lathe-Drill-Mill-Morse-4-MT4-ER40-Collet-CHUCK-Holder-NEW-/171243575817?pt=LH_DefaultDomain_3&hash=item27dee99a09 Where can I find a (male) #4 Morse taper with the tang to (female) ER40 collet holder? The one pictured is on ebay, but the seller is in...
Top