What's new

Search results

  1. B

    Can I get some advice on Centerless setup? (been a while)

    Yeah. I read through those it’s just that I can’t find the information in any manual or online anywhere so I was looking for clarification
  2. B

    Can I get some advice on Centerless setup? (been a while)

    Hello. Been a while. Running a Cincinnati #2 grinder at a new job and just wanted to clarify that the work rest and grinding wheel should be parallel. The grinder is set up now to where if I bring the wheel to the work rest, when it touches on the exit side there is .040-050 gap on the entry...
  3. B

    Centerless Grinding Adjusting Tips, General and Correcting Hourglass

    Hourglass What type of grinder do you have? I would definitely try the rotating/swivel adjustment a little at a time and try to reference your starting point so you can get back there if needed
  4. B

    Centerless wheels

    Just a question. Does the size of the regulating wheel matter in comparison to the grinding wheel. Seems like both times I’ve changed grinding wheels at work. New wheels 20” worn wheel maybe 16”. Grinds better with the smaller wheel. Not sure size of regulating wheel now but seems pretty worn...
  5. B

    Bar grinding

    I put the bars in the fixture and roll them until they start to grind. It seems as if when I am even(level) on the entry rolls. And flat on the blade(first 6 inches) entering the wheels, if I push the bar through, on the exit side I am .050 to .085 off the blade. And to get it even on the blade...
  6. B

    Bar grinding

    Anyone ever grind below center?
  7. B

    Bar grinding

    Picture of support entering grinder. When it ran decent.
  8. B

    Bar grinding

    Trying to figure out how to add a picture but it seems no matter what I’m doing I have to be slanted down hill entering the grinder in order to be even against the work blade. Blade not sitting on any thing. Cleaned pocket out real good.
  9. B

    Bar grinding

    Seems like the blade may be going downhill but not 100% sure. Really helped grabbing end of bar and pulling slightly away from grinding wheel. Not the best or safest solution but seems to work.
  10. B

    Bar grinding

    Hey. It’s been a while. Got a job about a month ago centerless grinding steel bars not sure what kind of steel. 1 1/2 to 4” bars 12-24 ft. Having lots of problems. No one to really discuss them with right now. One guy quit, one hurt his shoulder. 24” x 20” wheels. Having a problem with a section...
  11. B

    Centerless balancing

    What is the ring I'm checking for? Lol
  12. B

    Centerless balancing

    Down to about 9/16in of wheel above the recess. Can't find information on when they could break just that wheels are like glass. Idk wheel manufacturer has not answered me
  13. B

    Centerless balancing

    Shared album - Rob Gillispie - Google Photos
  14. B

    Centerless balancing

    Put old wheel back on today. (Despite its small size)Actually got a job finished. Anyone have info on how small a wheel can get and be safe. The part that hangs over the recess for the flange is maybe 3/4 inch
  15. B

    Centerless balancing

    In Norton catalog. Pen parts?
  16. B

    Centerless balancing

    Maybe able to give it a shot Monday. Someone is on vacation
  17. B

    Centerless balancing

    Guess I should have mentioned we do 3 passes on each part. Probably do 75-100 parts per order. Still not back on the machine today. Which is ok with me. Lol.
  18. B

    Centerless balancing

    Makes sense. I also noticed yesterday (before he pulled me off the machine) after I dressed the wheel and ran a few parts there were marks at the first and last inch of the grinding wheel. Like it was grinding heavier there. I will try adjusting th angle. Thank you again!!
  19. B

    Centerless balancing

    Not a dead try. Just a u-12 grinder and hourglass shape or s straight taper sometimes
  20. B

    Centerless balancing

    6" wheels. What is diamond set over. I don't think I have that on this machine. Our Cincinnati has an adjustment like 0-1 in the diamond holder or something like that but not the unison. I can just make sure they are set the same. Around 2.5 degreesto start?
Top