D1-6 tooling.
Jacobs flex collet chuck with 2 boxes of collets.
Asking $500 shipped.
Hardinge Sjogren Speed chuck with full set of 25 hardinge 3J collets $750 shipped.
6 backing plates.
1 of the backing plate I believe is for a Bison adjust-tru chuck and is 8 1/4" diameter. 2 are around 7 7/8"...
Palmgren 8" cross slide rotary table with tilt. Link to specs below. Nice condition, been on the shelf a while and was well-oiled. This has seen minimal use. I have never cleaned it up, only sprayed with oil and stuck it on the shelf. A little cleaning and it should look excellent.
Located in...
I have (2) Erickson #40 NMTB holder with collets. Both sets are new but have some light rust spots on the collets.
Also have 13 other #40 nmtn holders, (2) of 1", 3/4, 5/8 and 1/2". 1 each of 7/8, 5/8, 3/8 and 3/16. 2 arbors. These all look used except for the one threaded stud arbor.
I am...
All items located in 18640 Pittston Pennsylvania. Please obtain your own shipping quotes.
Troyke DMT-18 rotary table. 15x15 square table with x&y axis. Very impressive and heavy rotary table. Asking $400 . It's at least 500 lbs on a small skid.
Tru-trace set up. Single axis slide with stylus...
Nardini 1440 removable gap lathe. Threads metric and standard as well as dials in both measurements. Has a 1.875" spindle bore and D1-5 mount.
Comes as pictured with 3 and 4 jaw chucks, collet chuck, steady rest, follow rest, taper attachment and various top jaws. Very nice and well equipped...
South bend heavy 10 parts....
I did a part out on a heavy 10 with terrible ways.... here is whats left. If its not in the picture, its gone.
Complete cabinet with new 120v motor, pulleys. drum switch and all.
Headstock less spindle.
Lead screw and support.
Complete apron less hand wheel and...
I have a logan lathe with a motor that the tag reads 220/440 volt, but only has 3 wires coming out of it.
tag says its a Squirell cage indiction motor. It also says " This motor will operate successfully on 208 volts.
I have 220v 3 phase with a rotary converter set up. When i turn the machine...
Model A Monarch.
14 x 48. It's a pre serial number machine so it dates 1927 or older. Very impressive machine for its age. Ways are good and the machine seams operable as is or a perfect restoration machine. Also has the gearbox to change RPM, but does not have the original mounts for it and...
I recently grabbed to Model A to sell for a friend.
It is stamped Model A lot 500 machine 8.
Is there anyway to determine the year it was made. All i can dig up on the googles is 1927 and earlier are Lot/machine numbers instead of serials.
This thing is cool, even thuogh its going to a new...
Seimens motor, 3 jaw micro adjustable chuck, heavy well made housing and spindle. Comes with cables. This was off a prototrak machine I purchased and never used. The guy I got it from was running the entire system off a pc and software. Little surface rust from being in my storage bit is in good...
As the topic says, I am looking for a supplier of cold finished angle. It's a non critical part but the customer demands cold finish for cosmetic reasons.
Looking to purchase 1/8" thick 1.5 x 1.5 lenghts of angle. Can be press bent or rolled.
Any leads would me appriciated. thanks!
I have the chance to grab a 354 invision machine, without a wire feed for a very reasonable price. I have never used one... I have used a 350P several times with excellent results on aluminum, bronze, SS and others.
Up till this past year %99 of my work has been tig, since December I have...
I have a very cool air over hydraulic, 5 ton 600 degree press.
I picked it up at a sale heats ago and used it to heat and press 2 thin machined aluminum plates around a bearing. A retired mold maker stopped by and told me that he seen a machine just like it used to make breast implants. Is...
Steady rest for a Leblond 15" servo shift for sale. 4 3/8" capacity, brass pads and in good shape.
$1000 cash or Paypal with shipping included.
Located in Pittston, PA 18640
Long story short, At an estate sale there were a few BIG engines and parts that followed me home from an estate sale. Two crates of (8) cylinder sleeve liners for old Superior / white PTD-8 diesel engines. I purchased them for sub-scrap prices knowing I can atleast make a few bucks if I scrap...
I have a job that is under contract as a monthly deal so buying/building a machine for one job in this case is worth the investment. The job requires "grinding" the edges of 1/4" plate so they are smooth to the touch. I don't mind doing this when the weather is nice and I can do it outside. In...
I am posting this for a friend who needs help figuring out some programing issues they are having with this machine.
TREE vmc with TPC2100 controller. He is located in Reading, PA. If you can help him out on-site or possibly over the phone please contact him directly with your rates and...
What is a reasonable range for these collets? I have been doing a lot of metric parts lately and was wondering if am ok running metric end mills in std collets such as 12mm (.472) in a 1/2 collet or should I get some metric collets? I have done this over the years with no problems but not...
As the title reads....
Bought a brand spankin' new Kama Bandsaw. I purchased it through Fastenal on close-out and it was deeply discounted.
The meatheads at fastenal had it on its side and the gear lube came out the vent and was all over the cabinet of the saw. Upon wiring it up and trying it...
A lot of coolants say they are good for all machining, grinding and sawing while others claim they are made for just sawing. I bought a brand new kama saw and was debating on buying coolant just for sawing such as lenox's line of sawing coolants or just use what I have all ready.
Thoughts?
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.