What's new

Search results

  1. B

    WTB Schaublin 70 slide- inch

    I sent you a PM about a inch slide I have, thanks, Barry
  2. B

    Buck 3 jaw set true chuck 8" D1-4

    Sorry, misspelled set (se) and also wanted to add that jaws in place are reversible
  3. B

    Buck 3 jaw set true chuck 8" D1-4

    Hello Group, I am selling a 8" 3 jaw Buck set true chuck in nice condition. D1-4 mount. Comes with extra se of outside jaws. I purchased it for my Schaublin 135 but its too big and heavy for it. It comes with chuck key as well as allen wrench. Guessing shipping weight will be in the 30-35lb...
  4. B

    K.O. Lee cutter grinder model BA860

    Meant to add my email to the listing of the KO Lee, please reach out to [email protected]
  5. B

    K.O. Lee cutter grinder model BA860

    This is a great little KO Lee cutter grinder that I cleaned up many years ago and never ended up using. Comes with assorted wheels, extra hub and a new coolant tank pump. Runs on 3 phase but easy candidate for a VFD. Nice thing about this grinder is it disassembles into easily manageable parts...
  6. B

    I am interested in your SIP, can you give me a call when you have a minute, thanks, Barry 518...

    I am interested in your SIP, can you give me a call when you have a minute, thanks, Barry 518 496-0123
  7. B

    Need MT5 to B32 collet adapter for Schaublin 135

    I was at Hassig in Switzerland a few months ago and purchased several new mt5 to MT 4 reducers and I believe he had a MT 5 to B32 adaptor but unfortunately may be difficult to have them search for it. Christian died last year and his son Daniel had taken over. Very easy to deal with. I dug...
  8. B

    Arnold/Dapra hydraulic vise

    I purchased this vise to go on my Schaublin 13 but unfortunately its too large. The Jaw width is 4-5/8" and it weights over 60 lbs. The swivel base has a hole spacing of 4-1/2" outside of slot to outside of slot, slot width is just over 1/2". It is in excellent condition and beautifully made and...
  9. B

    WTB or trade 6" Buck Adj-tru 3 Jaw D1-3 Backplate I have the D1-4 size

    I see this is quite an old post but if the d1-4 backplate is still available I have a d1-3 buck adjust true plate that I can trade you ? I would also be willing just to purchase your backplate. I have the opposite problem as you, thanks, Barry
  10. B

    FS Fehlmann Swiss made coordinate table

    Looking to sell a Fehlmann Swiss compound table. This is a high precision coordinate table that is also heavy duty enough to use as a milling table. The table size is about 17"x 8". The model number is FS 200. It is a metric table. It is very heavy, guessing about 175 lbs crated. I can crate for...
  11. B

    Project Schaublin 135

    Hi Mark, Just to clarify there was defiantly no sleeve in mine, the pulley was solid cast iron. I think the difference you are seeing in the material near the brass holes I filled was just a relief recess that I cut in to make sure the new seal could seat properly.
  12. B

    WTB WTT D1-4 6" zero set Buck back plate for D1-3

    I am looking for a D1-4 buck 6" adjust true backplate to buy or trade for the original D1-3 Backplate that came on the chuck. I would also sell the D1-3 to any interested parties. Looking for $150 plus shipping to sell instead of trade. thanks, Barry
  13. B

    Project Schaublin 135

    I am interested in ordering decals for the speed band and dials as well, can you tell me where you ordered them from? thanks, Barry
  14. B

    Schaublin 135 Variable speed pulley issue

    The problem with changing to bearings and eliminating the oil system is that there is not enough room on the carrier tube to bore to fit them. I was hoping to do that as that would definitely be the better option. In speaking with someone who completed this option of changing to lip seals, he...
  15. B

    Schaublin 135 Variable speed pulley issue

    A better picture of the O ring seal on the sliding sheave that I want to machine out to allow for the lip seals
  16. B

    Schaublin 135 Variable speed pulley issue

    Schaublin 135 update So I got the drive removed and it has the arrangement of lip seals on the outer sides of the fixed 1/2 of the sheaves and O Rings on the inner sliding sheave so after consulting with a nice chap in Australia I’ve decided to follow his advise. As mentioned I think the o...
  17. B

    Schaublin 135 Variable speed pulley issue

    I will let you know what plan I will follow once I have the system apart and can determine what configuration it is, Thanks, Barry
  18. B

    Schaublin 135 Variable speed pulley issue

    I am looking for advise on my newly acquired 135 lathe. I purchased it as non working because the variable speed drive pulleys were froze up but I read that was a common issue. By the time the machine made it home on its 2 1/2 hour trek the pulleys had freed themselves up. After reading several...
Back
Top