Purdy sure the vector drive is the culprit.......seems to be quite a few places out there that repair and or exchange them. Just looking for a reputable outfit. Suggestions?
Putting my feelers out for a Brother Speedio 700..........not in a super rush, but should be needing another spindle soon. Must be clean. Low-ish hrs. 10k high torque or 16k spindle. No 27k spindle.
I have Milsuckee cordless tools and looking at a 1/2" drive impact.........
Milsuckee impact
How do they compare to a decent IR pneumatic rig? Or other air impacts............Performance wise? Even close?
IR gun
I know they both give some specs................but what are they like in real life?
I had someone ask if I could make an urn for their ashes when they pass. They want it made of metal.............Something machined. I figger, why not? Average volume is 1 cubic inch for every lb of the person. 6"Ø x 7" deep. Lookin to make a metal jar with a screw on lid. Prolly a bit of...
Are these drops worth peddling? 1.25"x1.50"x17"+/- 6061. Few hundred pcs and adding monthly. Sat outdoors so there's corrosion on some surfaces. Tired of them getting in the way...................though I'd maybe have the kid sell them for some extra $$......
Gonna mount this anvil to a block of white oak............sure I can make some straps or some kinda clamps with lag screws. But I was ponderin' just throwin' it up on the mill and drillin' 4 angled holes, one on each leg, and just laggin' it down that way............nice clean lookin' and...
I have new GMC 2500HD that is not equipped with the factory fifth wheel prep package(four pucks and the center ball flip receiver). Gonna pull a camper and prolly a gooseneck trailer. Looking into my options..........do I put in a goose neck ball though the bed and then use a fifth wheel plate...
I have 2 conex boxes sittin 10' apart. Gonna throw a roof 10' wide between them. Essentially making a car port...........Just wonderin what would be the best way to mount my a plate to hang my rafters..........Thinkin of a 2x6 green treat lyin flat on the top corners and settin rafters on that...
I have a 2013 DNM500 with the standard factory TSC. I'm down to my last bag filter with no reference of what brand or where they came from. (Bought the machine used a few years ago and it came with a pile of new filters.) Source?
Just starting to look............anyone have a late model low hour rig? My current 500 came from a PM member. S500 or S700. I wish I had the room as a S1000 would be great.10k or 16k spindle. Probing...............
I know that the usual suspects have units on their sites.........not really...
Lookin at drillin some deep (and straight) holes.............4375"Ø 12-14" or so deep. 4140HT. What say you? I ain't got high pressure coolant. 135PSI. Drill a pilot and have at it? Can it be done? And I got time. This doesn't need to be punched through in 30 seconds or...
So I'm assuming all three run very similarly.....I've only dealt with 2024 which is a dream to machine........any reason to source one over the other? Availability & price?? Not many local vendors carry any of 'em........I'm looking at 6k lbs..................suggestions for a vendor here in the...
So I run OP1 a longish part that doesn't lend to a stop in the draw tube. Clamp on material stickin outa the chuck 2" or so. Hit cycle start. Turret comes down with a stop in an ID tool holder 4.5" from the chuck. Now I want to be able to hit the pedal(unclamp) manually bring the stock to the...
So odd occurrence..............somehow the previous part was caught up in a rats nest of stringy chips that was hanging on the turret. Lathe pulled the bar, ran the next part, and when it came to cut off, the hanging part must have gotten wedged between the turret and the collet chuck. The lathe...
Just wondering size? I want to have enough. 2400 SQ FT. I have mist collectors, but there's plenty o humidity still in the air. Plus ya get snow melting off the tractor, lift, pallets, or material.....she's usually a bit damp. Get's a little swampy smellin too...............so size? I see 100...
8" power chuck 1.5mm x 60...........I checked Monster Jaws.............I buy softies from them. Lookin at their hardjaws.......not very aggressive teeth. Who makes some with more bite that doesn't break the bank??
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.