What's new
What's new
By:
Advanced search…

Search results

  1. A

    D4 Programming Question

    Don’t have a programming solution for you. Really don’t see a way to automate what you are doing because you have to inspect the initial bore and then choose which to overbore I am assuming you are boring the throats, then fitting oversize throttle plates. Question is why not standardize on an...
  2. A

    FP4NC with NC-T400

    Have rented "similar" drop deck trailers for machine moves. Worked pretty well..My issue was that the batteries that powered the hydraulics were almost always close to dead. Always brought along a good battery and jumpers, just to be sure.... Cheers Ross
  3. A

    FP4NC with NC-T400

    Man, wish you hadn’t mentioned this. Kept me awake last night thinking about that table. Cheers Ross
  4. A

    FP4NC with NC-T400

    Photos of the offering if I’m not mistaken showed two coolant tanks, so once upon a time there was a second Deckel. Did Porsche 4 cam cases , line bore the mains, rebored the jack shaft housing and the oil pump case bore after trimming the case joining faces. Don’t think I would attempt this...
  5. A

    For Sale ! ! !

    I believe it’s integral. However, Singer sells cute little threaded sleeves that convert the threaded end to the pull stud used by both Deckel and Maho CNC’s Cheers Ross
  6. A

    For Sale ! ! !

    FS Genuine Wohlhaupter #40 arbor, fits Deckel (20x2.0) thread. $100.00 plus shipping This fits the UPA3 boring heads that have removable shanks. Never used in my ownership.(appears to be new,never mounted) Complete with differential mounting screw. Last time i looked these were north...
  7. IMG_1668[1].JPG

    IMG_1668[1].JPG

    • AlfaGTA
    • Media item
    • Comments: 0
    • Album: Tooling
  8. IMG_1669[1].JPG

    IMG_1669[1].JPG

    • AlfaGTA
    • Media item
    • Comments: 0
    • Album: Tooling
  9. IMG_1670[1].JPG

    IMG_1670[1].JPG

    • AlfaGTA
    • Media item
    • Comments: 0
    • Album: Tooling
  10. IMG_1671[1].JPG

    IMG_1671[1].JPG

    • AlfaGTA
    • Media item
    • Comments: 0
    • Album: Tooling
  11. A

    (Not Deckel) Making a new cross leadscrew

    Almost impossible to get a true thread on something that long with a die..... There are machines that can do this but the die is driven by a lead screw and guided to keep it aligned.... Baring that your only DYI that will produce something worth installing would be to single point the...
  12. A

    Is this leg to high?

    Most CNC's use a single phase leg to power the logic side of the control. That leg is too high, as already stated.( no help there) In addition the logic side of the control should be connected to the non generated output of your converter.... Cheers Ross
  13. A

    New to me fp4nc with 3m control

    Spindle bearings are grease packed. Some heat is normal when running At full chat. Factory says that 120*f is OK when running at high RPM’s for extended periods. Cheers Ross
  14. A

    Need help with Error 20 on my Deckel FP2NC Dialog 3

    Keep us posted. Number of folks have passed by this spot and disappeared into the woods beyond. Your project sounds interesting, we be folk here that work with our hands, and hold high actual physical results Wishing you success, and further information on your progress. Cheers Ross
  15. A

    Deckel fp3 nc

    Don’t scratch the glass scale. Lint free cloths and 99% isopropyl alcohol as a cleaning solution. Remove the end caps and remove the read head. There are postings on this board that go over all this. Do a search , poster “balen” Check the link provided by rklopp above. Cheers Ross
  16. A

    Deckel fp3 nc

    Scale is a smaller section ( LS 903) that fits on that Deckel. No longer avaliable from Heidenhain. Modern scale will not fit in the space available without some mods to the machine. Last time I checked Deckel had new old stock replacement scales. Cost several years back was $4000.00...
  17. A

    MH300 - Z (vertical) axis handwheel drive shaft mystery bolt

    So can't see the bolt/screw well enough to tell. Is it an Allen style set screw, or a slotted head screw? Since it has no head on the surface its only function would be retaining/locating something inside that casting, most likely a bushing, or its like Bruce surmises as being a lube point...
  18. A

    RPC sizing for FP3NC

    Bear in mind that value is for 380 v supply. 220 supply to the transformer would then need about 38 amps of capacity. Cheers Ross
  19. IMG_1667[1].JPG

    IMG_1667[1].JPG

    • AlfaGTA
    • Media item
    • Comments: 0
    • Album: Msc Deckel 2
  20. A

    RPC sizing for FP3NC

    Connected loads are higher on the FP3NC. Larger drive motor, and larger servo motors ( “Z” ) My main electrical cabinet on my FP3NC ( flip) data plate is marked “22 A “ (not KVA) In my manual for the same machine in the general data the 380v connected load is called out as “ aprox 14.5 KVA”...

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top