What's new
What's new

FS: 1969 Monarch 10EE Toolroom Lathe

Mark999

Aluminum
Joined
Mar 29, 2018
Due to health reasons, I'm forced to liquidate my shop. I've owned this lathe for several years. The original module drive was removed before my purchase and it had a Warner Seco drive in its place that wouldn't go much above 1000rpm. Currently it has a Parker Eurotherm 514-C 32amp drive for armature power and a Parker 507 for field power. Control is the same as original but is done through an Allen Bradley PLC and the ELSR micro-switches. All drive keys in the apron were replaced and the oil system cleaned and tested.
This machine was originally ordered for American Bosch Arma Corp. and was tooled up for non production use. I've been scouring the internet looking for pieces that have gone missing according to the original invoice. Below is the current state:

Monarch Tooling Cabinet
Taper Attachment
Steady Rest
Follow Rest
Carriage Micro-stop
Face Plate
Dog Plate
Micrometer Carriage Stop (4-sta multi pos)
Diameter Stop (4-sta multi pos)
Micro-Gauging Diameter Dial
8in TMX 6 jaw chuck (New)
Sjogren 2J collet chuck
Partial set of 2J collets
Jacobs Flex Collet chuck
Full set of Flex collets for Jacobs chuck
8in. 3 jaw chuck
6in. 3 Jaw chuck
8 in. 4 jaw chuck (New)
5c collet adapter
Dorian BXA tool post with 7 holders
MT2 Live Center
MT2 drill chucks (2)
Jarno taper center for spindle
Enco Bed Turret with a variety of holders (needs an adapter made for 10ee)
Lots of cutting tools with inserts, if it's lathe related, it's going with it.
Location: Spokane Valley, Wa. Price $10k
PM for contact info.
Being disabled, I can open the shop for you or your riggers, but can't do much else.
 

Attachments

  • Dscf7965.jpg
    Dscf7965.jpg
    86.6 KB · Views: 324
  • Dscf8150.jpg
    Dscf8150.jpg
    87.2 KB · Views: 336
  • Dscf8151.jpg
    Dscf8151.jpg
    85.9 KB · Views: 341
  • Dscf7969.jpg
    Dscf7969.jpg
    89.3 KB · Views: 463
  • DSCF7962.jpg
    DSCF7962.jpg
    90.6 KB · Views: 362

bsg

Titanium
Joined
Jan 17, 2003
Location
Imlay City, Michigan
Due to health reasons, I'm forced to liquidate my shop. I've owned this lathe for several years. The original module drive was removed before my purchase and it had a Warner Seco drive in its place that wouldn't go much above 1000rpm. Currently it has a Parker Eurotherm 514-C 32amp drive for armature power and a Parker 507 for field power. Control is the same as original but is done through an Allen Bradley PLC and the ELSR micro-switches. All drive keys in the apron were replaced and the oil system cleaned and tested.
This machine was originally ordered for American Bosch Arma Corp. and was tooled up for non production use. I've been scouring the internet looking for pieces that have gone missing according to the original invoice. Below is the current state:

Monarch Tooling Cabinet
Taper Attachment
Steady Rest
Follow Rest
Carriage Micro-stop
Face Plate
Dog Plate
Micrometer Carriage Stop (4-sta multi pos)
Diameter Stop (4-sta multi pos)
Micro-Gauging Diameter Dial
8in TMX 6 jaw chuck (New)
Sjogren 2J collet chuck
Partial set of 2J collets
Jacobs Flex Collet chuck
Full set of Flex collets for Jacobs chuck
8in. 3 jaw chuck
6in. 3 Jaw chuck
8 in. 4 jaw chuck (New)
5c collet adapter
Dorian BXA tool post with 7 holders
MT2 Live Center
MT2 drill chucks (2)
Jarno taper center for spindle
Enco Bed Turret with a variety of holders (needs an adapter made for 10ee)
Lots of cutting tools with inserts, if it's lathe related, it's going with it.
Location: Spokane Valley, Wa. Price $10k
PM for contact info.
Being disabled, I can open the shop for you or your riggers, but can't do much else.

Sorry to hear about the health issues!

That's a beautiful machine and well equipped, I would be seriously considering this if I hadn't just bought another machine, when it rains it pours!

Good luck on the sale, and take care of yourself!

Kevin
 

thermite

Diamond
Adding to best wishes going forward with the health.

That's a proven winner as to re-powering, and there are now several among us who understand it and/or have documented it .."right here, on PM".

Both DC Drives are still in channels, brand-new as well as used, so the next owner can expect to enjoy it for many years with low-risk as well.

Best,

Bill
 








 
Top