Pole Barn Machine Shop

[Fal Grunt]

I remember that Moore, have you run it yet to find out if it is a decent machine?

 

[alskdjfhg]

Paint is in bad shape, but its a great machine under that.

Sent from my SM-G965U using Tapatalk

 

[Fal Grunt]

Good, glad to hear it!

 

[alskdjfhg]

Its too small to do anything on, but also way to nice go get rid of

Sent from my SM-G965U using Tapatalk

 

[Fal Grunt]

Oh I use my Moore almost weekly, it’s fantastic. However, the scale of my work is significantly smaller than yours!

 

[TXJACK]

alskdjifhg- I just joined and tried to send you a question through private, but it says your mailbox is full. This post reply was the only other way I could think of to let you know.

 

[alskdjfhg]

The drill showed up Sunday. Bit of a cluster fuck to get it moved but its done.

Not quite as nice as I was hoping, but nothing major.

Seem like I got a bad motor starter/contactor for the arm elevation, bad bearing in the spindle motor, worn out spline on headstock input gear, and potentially some bad headstock bearings.

Got the motor torn apart and order those bearings. Once I get those replaced, proably use it as is for a little while then rebuild the headstock.

 

[johnoder]

Looks sturdy. Glad it came with a useful looking table

 

[alskdjfhg]

https://youtu.be/N50IMuFjiRM

Video of the shaper cleaning up some burn outs

Sent from my SM-G965U using Tapatalk

 

[johnoder]

Belt guard is here when needed - though the belts may need to be different

 

[alskdjfhg]

Working stupid hours at work, so haven't done any work in my shop for a while. Working 7 days a week 12 hr shifts in a machine shop takes alot of the desire to work in my own shop away.

Today moved the drill press a bit out of the way. Not sure if I like that spot, but its easy to move if I don't.



Sent from my SM-G965U using Tapatalk

 

[alskdjfhg]

Busy weekend, but productive.

Got most of the way done on modifying and installing the new gantry crane.

Friday a 40' beam and some channel bracing showed up. Brought it into the shop Saturday, welded it together Sunday and got everything ready to raise the legs up install the wheels for the crane.

Now quite sure how I'm going to do that yet, but shouldn't be too hard.

Pictures are failing to upload. Will try later


Sent from my SM-G965U using Tapatalk

 

[alskdjfhg]

Pictures

Sent from my SM-G965U using Tapatalk

 

[alskdjfhg]

Pictures

Used the Miller Big 50 and some 5/32 7018 rod to glue the channel top cap brace to the S18x54.7 beam

Sent from my SM-G965U using Tapatalk

 

[alskdjfhg]

Flipped the beam wirh the big Hyster cause I ran out of propane for the TCM.

Sent from my SM-G965U using Tapatalk

 

[alskdjfhg]

Largest PITA was removing the legs from the old beam. They are made out of aluminum, and some asshole decided that countersunk Allen head set screws should hold them in place. They had sized up, and it was a major paid to disassembly. And some threads had to be oversized.

Sent from my SM-G965U using Tapatalk

 

[alskdjfhg]

Got the crane stood up yesterday, not too bad but having help is essential.

Sent from my SM-G965U using Tapatalk

 

[alskdjfhg]

Friend that was helping took a short video of raising it up.

Setting Up a Wallace Gantry Crane - YouTube