What's new
What's new

WTS/WTT: Hardinge-Sjogren D1-6 2J chuck and various 2J collets

paroikoi

Aluminum
Joined
Oct 2, 2014
Location
Jonesboro, AR, USA
Up for sale or trade are the following:

Hardinge Sjogren 2J D1-6 speed chuck with 24 2J collets. Good condition and works great. Includes set of 21 2J collets from 1/8" to 1-3/8" by 16ths. All the included collets are Hardinge except for the 13/16" which is Rivett and the 1-3/16" which is Buck. Also includes 3 shop-modified 2J collets: a 1-1/4" round, 1-5/8" round, and 1/2" hex. $499 plus actual shipping (less than I have into it). If it matters to you, I have a Hardinge 13/16" 2J collet below I could swap with the Rivett.
PXL_20210620_220143612.jpg
PXL_20210620_220227161.jpg

Lot of 14 Hardinge metric 2J collets. 6mm through 20mm by 1mm except no 14mm collet. $499 plus shipping.
PXL_20210521_010957370.jpg

Lot of 19 2J collets. This is almost a full set from 3/16" to 1-3/8" by 16ths, except that no 5/16" collet is included. Good condition overall, but some have minor damage that shouldn't affect use. All are Hardinge except the 1-3/8" collet, which was made by Balas. $349.
PXL_20210523_201021662.jpg

Hardinge metric 6mm 2J collet. $35.

Various 2J collets in good condition. Various brands. 7/16", 1/2", 11/16", 3/4" (qty 2), 13/16", 15/16" (qty 3), 31/32", 1-1/8" (qty 2), 1-1/4", 1-3/8". $13 each.
PXL_20210425_190052206.jpg

Various 2J collets in fair condition. Various brands, some unreadable. All have more damage or wear than the "good" condition collets above. 9/16", 3/4", 13/16", 7/8" (qty 2), 15/16" (qty 2), 1", 1-5/16". $10 each.

Various other 2J collets in good condition. Hardinge 5/32", 15/64", 9/32", 25/64", 13/32", 15/32", 33/64", 19/32", 49/64", 1-17/64". Modern brand 1.100", may be shop-modified. Shop-modified 3/8" and 1/2" hex. All these are $15 each.

I can provide more photos on request. Note that the list of individual collets above should be correct, but the photos show more than are available as some have been sold since I took the photos.

None of the prices above include shipping, but I will combine shipping and only charge actual cost.

Trades I'm interested in include an Aloris or Dorian BXA tool post or holders, a 5/16" 2J collet (to complete the set above), a D1-3 4-jaw chuck (either a 10EE "lightweight" Cushman or a regular 6"), 10EE square dial metric change gears, a 10EE square dial follower rest, an MT2 live center, and MT2 dead center, or specific 5C collets (hex or square collets, step collets, or round collets smaller than 1/16").
 
Interested in the collet chuck and collets. I do have an extra Armstrong BXA Tool post if you are interested.

Thanks,
Paul
 
OK. what is your best price on the chuck and collets?

Paul

My listed price is my best price. It's already less than I paid for it and less than it should go for on eBay. I just listed it on eBay yesterday for a lot more. If it doesn't sell there, I will go down slowly over time if I need to, but it will be a while before it gets down to the price I have it listed for here.
 








 
Back
Top