HELP Anilam 3000M disks
Close
Login to Your Account
Results 1 to 11 of 11
  1. #1
    Join Date
    Nov 2013
    Country
    UNITED KINGDOM
    Posts
    10
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default HELP Anilam 3000M disks

    Hi

    I have just purchased a 5000VS milling machine but didn't get any floppy disks with the machine. The cmos battery was dead. I have replaced it but I need the bios config file to set up the bios for the machine.

    I have loaded default values and it it all powers up but I get I/O nodes different to install when trying to power servos. All the dro works but even in manual mode it wont run the spindle. Again I think this is just an I/O problem.

    40.2-12.jpg

    Any help will be gratefully received and am more than happy to pay for copies of disks and/or your time to complete my request.

  2. #2
    Join Date
    Aug 2018
    Country
    UNITED STATES
    State/Province
    New York
    Posts
    20
    Post Thanks / Like
    Likes (Given)
    1
    Likes (Received)
    16

    Default

    Please e-mail me @ [email protected].
    I can get you what you need.
    Thanks, Jerry from JB CNC Repair, LLC.
    PH# 716-490-1462.

  3. Likes HWElecRepair liked this post
  4. #3
    Join Date
    Nov 2013
    Country
    UNITED KINGDOM
    Posts
    10
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    Quote Originally Posted by Jerry Bouvier Jr View Post
    Please e-mail me @ [email protected].
    I can get you what you need.
    Thanks, Jerry from JB CNC Repair, LLC.
    PH# 716-490-1462.
    Jerry, Thank you so much for your response. Email sent.

  5. #4
    Join Date
    Sep 2016
    Country
    UNITED STATES
    State/Province
    Texas
    Posts
    6
    Post Thanks / Like
    Likes (Given)
    13
    Likes (Received)
    1

    Default

    I was working at Anilam when they started. Like seeing a crusader and such a clean shop too.

  6. #5
    Join Date
    Nov 2013
    Country
    UNITED KINGDOM
    Posts
    10
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    Quote Originally Posted by frank Texas View Post
    I was working at Anilam when they started. Like seeing a crusader and such a clean shop too.
    I am impressed with the quality of the wiring etc.

    2019-04-18-17.14.05.jpg

    and I am of the mind... a clean workshop is a safe workshop.

  7. #6
    Join Date
    Sep 2010
    Location
    Anchorage, Alaska, USA
    Posts
    628
    Post Thanks / Like
    Likes (Given)
    229
    Likes (Received)
    122

    Default

    [email protected]
    This is your solution.
    Don knows it all.

  8. #7
    Join Date
    Sep 2010
    Location
    Anchorage, Alaska, USA
    Posts
    628
    Post Thanks / Like
    Likes (Given)
    229
    Likes (Received)
    122

    Default

    My shop is dangerous and dirty.
    I never seen one that wasn't...

  9. #8
    Join Date
    Nov 2013
    Country
    UNITED KINGDOM
    Posts
    10
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    Quote Originally Posted by Jerry Bouvier Jr View Post
    Please e-mail me @ [email protected].
    I can get you what you need.
    Thanks, Jerry from JB CNC Repair, LLC.
    PH# 716-490-1462.
    Hi
    Thanks for the information, I will give him a try.

  10. #9
    Join Date
    Nov 2013
    Country
    UNITED KINGDOM
    Posts
    10
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    Quote Originally Posted by snowshooze View Post
    [email protected]
    This is your solution.
    Don knows it all.
    Thanks you for your input, Yes, Don Is on case and extremely helpful. Thank you once again.

  11. #10
    Join Date
    Nov 2013
    Country
    UNITED KINGDOM
    Posts
    10
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    Quote Originally Posted by LotusRallyman View Post
    Jerry, Thank you so much for your response. Email sent.
    Hi
    Just for information... I never got a response from this guy

  12. #11
    Join Date
    Nov 2013
    Country
    UNITED KINGDOM
    Posts
    10
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    Quote Originally Posted by LotusRallyman View Post
    Thanks you for your input, Yes, Don Is on case and extremely helpful. Thank you once again.
    Hi

    An update.... Don Schoof is clearly a wizard in disguise when it comes to Anilam CNC control. I'm in the UK he's in America yet with the exchange of emails and giving him photos of what he wanted to see HE has within three/four days sorted the thing out and I now have a fully functioning Anilam3000M CNC controlled Milling Machine. I can't praise the guy enough. His pinpointing of problems and giving me clear instruction as to what to do has been mind blowing. Yes, I also now know my way around this machine; a little better, but that doesn't detract from what this guy is capable of. Mere Genius.
    Don I can't thank you enough and I certainly take my hat off to your incredible knowledge of all things CNC. If ever your in the UK you have a place to stay here.
    Thank you, and a big thanks to Snowshooze who put me on to him.


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •