markp
Hot Rolled
- Joined
- Oct 7, 2006
- Location
- Petaluma CA 94952
Tried to program a simple polar pocket with three repeats on my DMG DMU103V and the program runs, (after my post guy made some changes to put an X -Y axis move on the same line as all the A axis moves and fix repeats), but the A axis moves are at the F speed of 16, in degrees per minute! Waaaay to slow. My post guy suggested that I replace G70 in line N6 with G700 but my control is too old to recognize it.
This 4th was never used by the previous owner after initial install by DMG at purchase. I think there's some parameter that needs to be changed but rather than read through 5 or 10,000 pages of Siemens manuals or waste a few days getting no answers from DMG tech support, I thought Id ask here first.
%_N_6000_MPF
;$PATH=/_N_MPF_DIR
N1 TRANS X0. Y0. Z0.
N6 G17 G70 G40
N11 G64
N16 T23
N21 M6
N26 G54
N31 TRANS X0. Y0. Z0.
N36 S2000 M3
N41 G90 G0 X4.892 Y0. A-18.0934 M8
N46 Z2.
N51 LBL1:
N56 FGROUP(X,A)
N61 G1 Z1.8763 F16.
N66 G91 X.07 Z0. A-2.1109
N71 X-.14 Z0.
N76 X0. Z0. A40.4086
N81 X.14 Z0.
N86 X0. Z0. A-40.4086
N91 X0. Z0. A-3.0156
N96 X-.24 Z0.
N101 X0. Z0. A46.4398
N106 X.34 Z0.
N111 X0. Z0. A-46.4398
N116 X-.1 Z0.
N121 X0. Z0. A-3.0155
N126 X-.27 Z0.
N131 X-.0137 A.0405
N136 X-.0131 A.1201
N141 X-.0121 A.1951.............
N2161 X-.13 Z0.
N2166 G90
N2171 LBL2:
N2176 G0 X4.892 A-108.0934
N2181 REPEAT LBL1 LBL2
N2186 G0 X4.892 A-198.0934
N2191 REPEAT LBL1 LBL2
N2196 G0 X4.892 A-288.0934
N2201 REPEAT LBL1 LBL2
N2206 FGROUP()
N2211 Z2.
N2216 A-360.
N2226 TRANS X0. Y0. Z0.
N2231 M29 M30
This 4th was never used by the previous owner after initial install by DMG at purchase. I think there's some parameter that needs to be changed but rather than read through 5 or 10,000 pages of Siemens manuals or waste a few days getting no answers from DMG tech support, I thought Id ask here first.
%_N_6000_MPF
;$PATH=/_N_MPF_DIR
N1 TRANS X0. Y0. Z0.
N6 G17 G70 G40
N11 G64
N16 T23
N21 M6
N26 G54
N31 TRANS X0. Y0. Z0.
N36 S2000 M3
N41 G90 G0 X4.892 Y0. A-18.0934 M8
N46 Z2.
N51 LBL1:
N56 FGROUP(X,A)
N61 G1 Z1.8763 F16.
N66 G91 X.07 Z0. A-2.1109
N71 X-.14 Z0.
N76 X0. Z0. A40.4086
N81 X.14 Z0.
N86 X0. Z0. A-40.4086
N91 X0. Z0. A-3.0156
N96 X-.24 Z0.
N101 X0. Z0. A46.4398
N106 X.34 Z0.
N111 X0. Z0. A-46.4398
N116 X-.1 Z0.
N121 X0. Z0. A-3.0155
N126 X-.27 Z0.
N131 X-.0137 A.0405
N136 X-.0131 A.1201
N141 X-.0121 A.1951.............
N2161 X-.13 Z0.
N2166 G90
N2171 LBL2:
N2176 G0 X4.892 A-108.0934
N2181 REPEAT LBL1 LBL2
N2186 G0 X4.892 A-198.0934
N2191 REPEAT LBL1 LBL2
N2196 G0 X4.892 A-288.0934
N2201 REPEAT LBL1 LBL2
N2206 FGROUP()
N2211 Z2.
N2216 A-360.
N2226 TRANS X0. Y0. Z0.
N2231 M29 M30