Deckel LK LKS LKD
Close
Login to Your Account
Results 1 to 11 of 11
  1. #1
    Join Date
    Dec 2019
    Country
    SLOVENIA
    Posts
    15
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    2

    Default Deckel LK LKS LKD

    Hi
    I just got myself a Deckel model LK, known as jig borer. I need to overhaul it a bit because it was sitting for a while and was not in use for some time. I. Was searching for a manual but couldn't find any. Do we have someone here that is willing to send it to me as PDF via email?

  2. #2
    Join Date
    Dec 2019
    Country
    SLOVENIA
    Posts
    15
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    2

    Default

    Here is the photo of it...img_20200519_134214.jpg

  3. #3
    Join Date
    Dec 2019
    Country
    SLOVENIA
    Posts
    15
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    2

    Default

    I also couldn't get it to lower the head down by hand (wheel on the back right), like it's stuck. Is it possible to move Z axis without powering the machine on?

  4. #4
    Join Date
    Aug 2002
    Location
    France
    Posts
    1,663
    Post Thanks / Like
    Likes (Given)
    295
    Likes (Received)
    730

    Default

    I can't recall of any thread discussing LK machines on this board or anywhere else. Ever.

    When I say discussing, I mean by someone actually owning and using such a machine !
    Thinking about it,

    Good luck !

  5. Likes Laurentian liked this post
  6. #5
    Join Date
    Dec 2019
    Country
    SLOVENIA
    Posts
    15
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    2

    Default

    I think it would be great if we have a thread like this. This machine would deserve the thread, don't you think

  7. #6
    Join Date
    Sep 2008
    Location
    Canada
    Posts
    1,112
    Post Thanks / Like
    Likes (Given)
    444
    Likes (Received)
    426

    Default

    Well, I’ll be darned! I own a cool old Deckel that Tien doesn’t. Yet ;-)

    Yes, the Z axis, and the other axis as well, work without power. Just slower.

    I don’t have a manual or parts book for the LK either and would be interested in a copy as well.

    L7

  8. #7
    Join Date
    Mar 2001
    Location
    Switzerland
    Posts
    2,577
    Post Thanks / Like
    Likes (Given)
    2513
    Likes (Received)
    1141

    Default

    Does it have the electrical box?

  9. #8
    Join Date
    Dec 2019
    Country
    SLOVENIA
    Posts
    15
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    2

    Default

    Quote Originally Posted by Screwmachine View Post
    Does it have the electrical box?
    Yes it has two of them...and also it came with vacuum cleaner but sadly doesn't have a lid. Maybe originally they don't have a lid?

  10. #9
    Join Date
    Dec 2002
    Location
    Benicia California USA
    Posts
    8,302
    Post Thanks / Like
    Likes (Given)
    1931
    Likes (Received)
    2624

    Default

    For a short while i owned the conversion table that made a standard FP2 or FP3 into an LK...What i mean is Deckel built the same table that you have on your LK except it was made with a mounting
    face that bolted to the vertical table of the manual mills.(not FP1)
    Table had the optical scales and moved independent of the mill's slides....came with a frame work that carried the table with wheels allowing it to be rolled right up to the mill for mounting....
    Don't know much about the table , did not keep it long....
    Never seen any documentation on the LK's ...

    Be careful with the vertical head....Fits between the quill and the head casting are very close. Dirt and rust will be a problem there....There are two versions of head, A boring/drilling head, and a grinding head. Both were used with that machine.
    The quill is lubricated through a screw on top of depth stop rod (the bar on the front of the vertical head that has a small flat shelf on top) Move the bar (thumb screw) fully down.9after you clean off the rust) Remove the screw from the top of the flat shelf and apply oil into the hole....I would start with some light nachine oil to get things loosened up....


    The two cabinets contain the electrics for the machine(1) and the high frequency power source for the grinding spindle. Believe there are two versions of the high frequency supply, but i don't know more than that other
    than the first gen high frequency source is deemed troublesome....

    You do know that the ways on that table will make it useless for all but very light milling....Not designed to take side loads, just down thrust from drilling and boring...

    Cheers Ross

  11. Likes Laurentian liked this post
  12. #10
    Join Date
    Mar 2008
    Location
    Canada
    Posts
    1,133
    Post Thanks / Like
    Likes (Given)
    6684
    Likes (Received)
    209

    Default

    We bought a similar LK a decade ago for 1400 to nab the boring and drilling head, thinking we'd have use for it on our FP2. It sits there still in our cabinet's lower shelve unused.. Our shop neighbour kept some weird parts off it for possible use later as he's a millwright. Balance was carted off to metal recycling..

  13. #11
    Join Date
    Dec 2019
    Country
    SLOVENIA
    Posts
    15
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    2

    Default

    Alfa GTA I followed your advice also had to tap it on the lever to start to move the quill. It took me half a day to get it moving...back in my head I had this felling that i'm doing it wrong and will do some damage, but luckily this time it was a right way to loosen the quill. Thanks a bunch

  14. Likes Laurentian liked this post

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •