Panza
Stainless
- Joined
- Oct 23, 2005
- Location
- Lillehammer, Norway
I am running a turning job in annealed tool steel - 18mm diameter bar. The part is about 2" long and a little over 1/2" in diameter. Currently it takes 1 minute 56 seconds. I am looking to improve the cycle time. The program is made in VPS. I have made a few manual modifications, but I am sure there are lots of little things I can do to cut the cycle time. When I looked at it now on the computer I noticed the OD roughing cycle cuts lots of air where it already faced of the part due to the finish OD cycle doing the finish facing too. Any ideas are welcome, but be specific , my G-code skills are not epic.
I am running it in a NLX 2000 SY. I have attached the whole file too.
I have noticed one place in particular where improvements could be made: When going from the roughing cycle to finishing cycle with the endmill:
N9
(ENDMILL, 10.000, T521)
G0M5
M69
G98G19
M245
G28H0
G55
G0T0521
M8
G97S200M13
S4000
G0Z-5.5
X24.
C180.
M268
G0Y17.785Z5.832
X14.25
G1X-16.F4000.
Y13.878Z2.553F1250.
Y1.067Z-8.196
G2Y-5.811Z-10.7R10.7
G1Y-7.
Y-12.1
G0X14.25
Y15.985Z7.976
G1X-16.F4000.
Y12.078Z4.698F1250.
Y-.733Z-6.051
G2Y-5.811Z-7.9R7.9
G1Y-7.
Y-12.1
G0X14.25
Y14.185Z10.121
G1X-16.F4000.
Y10.278Z6.843F1250.
Y-2.533Z-3.907
G2Y-5.811Z-5.1R5.1
G1Y-7.
Y-12.1
G0X14.25
M69
X24.
Z-5.5
G28V0
M01
N10
(ENDMILL, 10.000, T521)
G98G19
M245
G55
G0T0521
M8
G97S200M13
S7500
G0Z-5.5
X24.
C180.
M268
G0Y14.121Z10.198
X14.25
G1X-16.F2000.
G41Y7.Z10.75F1000.
Y-5.811Z0
Y-7.
G40Y-12.1Z-5.
G0X14.25
M69
X24.
Z-5.5
G28V0
G53X-50.
G53Z-316.
M01
View attachment Program.txt
I am running it in a NLX 2000 SY. I have attached the whole file too.
I have noticed one place in particular where improvements could be made: When going from the roughing cycle to finishing cycle with the endmill:
N9
(ENDMILL, 10.000, T521)
G0M5
M69
G98G19
M245
G28H0
G55
G0T0521
M8
G97S200M13
S4000
G0Z-5.5
X24.
C180.
M268
G0Y17.785Z5.832
X14.25
G1X-16.F4000.
Y13.878Z2.553F1250.
Y1.067Z-8.196
G2Y-5.811Z-10.7R10.7
G1Y-7.
Y-12.1
G0X14.25
Y15.985Z7.976
G1X-16.F4000.
Y12.078Z4.698F1250.
Y-.733Z-6.051
G2Y-5.811Z-7.9R7.9
G1Y-7.
Y-12.1
G0X14.25
Y14.185Z10.121
G1X-16.F4000.
Y10.278Z6.843F1250.
Y-2.533Z-3.907
G2Y-5.811Z-5.1R5.1
G1Y-7.
Y-12.1
G0X14.25
M69
X24.
Z-5.5
G28V0
M01
N10
(ENDMILL, 10.000, T521)
G98G19
M245
G55
G0T0521
M8
G97S200M13
S7500
G0Z-5.5
X24.
C180.
M268
G0Y14.121Z10.198
X14.25
G1X-16.F2000.
G41Y7.Z10.75F1000.
Y-5.811Z0
Y-7.
G40Y-12.1Z-5.
G0X14.25
M69
X24.
Z-5.5
G28V0
G53X-50.
G53Z-316.
M01
View attachment Program.txt
Last edited: