Charmilles Robofil 380 RS232 error (fanuc)
Close
Login to Your Account
Likes Likes:  0
Results 1 to 6 of 6
  1. #1
    Join Date
    Sep 2021
    Country
    POLAND
    Posts
    4
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default Charmilles Robofil 380 RS232 error (fanuc)

    Hello,

    im running a 2005 Robofil 380, and i have problem with RS232. After starting machine there is "PMC W2158: RS232 LINE CHECK TIME DEFAULT", checked cable it seems to be ok, pulled out then putted in some plugs on boards and boards itself, after few times machine started normally. After sunday it constantly starts with this error.
    241864033_1228988364231673_6598769177190577804_n.jpg
    241754166_1220793315092194_8007347178597956193_n.jpg
    241756934_550954956180031_5970187723590049856_n.jpg
    241736721_1213799079141800_1119475358200138325_n.jpg

    Had same problem back in 2019, replaced "master" card but the error was still on, technician pulled out cable pluged it back in and it worked back then.

    Lower red diode is mostly on, sometimes its off, still have error. When its on lower cards (UPR) are off.

    Anyne had simillar error? Technician form Charmilles is not sure what it could be, he said we should start with replacing RS232 cable i not sure about it being source of it. Will replace it but have to wait for it.

  2. #2
    Join Date
    Mar 2019
    Country
    ALAND ISLANDS
    Posts
    39
    Post Thanks / Like
    Likes (Given)
    12
    Likes (Received)
    5

    Default

    Quote Originally Posted by Przeto View Post
    Hello,

    im running a 2005 Robofil 380, and i have problem with RS232. After starting machine there is "PMC W2158: RS232 LINE CHECK TIME DEFAULT", checked cable it seems to be ok, pulled out then putted in some plugs on boards and boards itself, after few times machine started normally. After sunday it constantly starts with this error.
    241864033_1228988364231673_6598769177190577804_n.jpg
    241754166_1220793315092194_8007347178597956193_n.jpg
    241756934_550954956180031_5970187723590049856_n.jpg
    241736721_1213799079141800_1119475358200138325_n.jpg

    Had same problem back in 2019, replaced "master" card but the error was still on, technician pulled out cable pluged it back in and it worked back then.

    Lower red diode is mostly on, sometimes its off, still have error. When its on lower cards (UPR) are off.

    Anyne had simillar error? Technician form Charmilles is not sure what it could be, he said we should start with replacing RS232 cable i not sure about it being source of it. Will replace it but have to wait for it.
    What does the fanuc i18 main controller leds show
    We must know more
    Can ypu please put the machine in english

    Sent from my SM-G975U using Tapatalk

  3. #3
    Join Date
    Sep 2021
    Country
    POLAND
    Posts
    4
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    BLAD ZASILANIA means POWER OFF, poor translation but its the message that shows up when turning off machine.
    1631547582336.jpg1631547582364.jpg1631547582350.jpg1631547582320.jpg

    Turned on mechine without rs232 cable pluged in, and the same messages are showing up. DoubleChecked cable with multimeter and there is a signal between plugs. Is it possible that there is signal but its to weak or slow or anything wrong with it?

  4. #4
    Join Date
    Mar 2019
    Country
    ALAND ISLANDS
    Posts
    39
    Post Thanks / Like
    Likes (Given)
    12
    Likes (Received)
    5

    Default

    Are you still down ....I'd not what did you end up finding

    Sent from my SM-G975U using Tapatalk

  5. #5
    Join Date
    Sep 2021
    Country
    POLAND
    Posts
    4
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    Im still waiting for that cable...

  6. #6
    Join Date
    Sep 2021
    Country
    POLAND
    Posts
    4
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    0

    Default

    UPDATE:

    After replacing cable it was still turning on with error and not working. Service came to check it again, installed newer software (did not help), then replaced master card and it helped, machine turned on fine.


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •