Electrically-insulating material selection
Close
Login to Your Account
Page 1 of 2 12 LastLast
Results 1 to 20 of 24
  1. #1
    Join Date
    Jul 2021
    Country
    UNITED STATES
    State/Province
    Idaho
    Posts
    13
    Post Thanks / Like
    Likes (Given)
    7
    Likes (Received)
    0

    Default Electrically-insulating material selection

    Any suggestions for a material that is:

    --Machinable with conventional carbide/hss tooling
    --Electrically insulating
    --Has a coefficient of thermal expansion ideally below 25ppm/degF (~45ppm/degC)

    ...and then it'd be nice if it...

    --costs less than $5/cubic inch in quantities of ~20 cubic inches.


    This is a low-voltage device, less than 10V across the part. Macor would work but it's overkill.
    It'd be good to discover something less expensive for this application.

  2. #2
    Join Date
    Apr 2004
    Location
    Modesto, CA USA
    Posts
    8,804
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    1734

    Default

    How thin can it be? for 10 volts I would think any plastic,dry wood or marble would work. wiring is pvc, nylon, teflon. I bet pex, polyethelene, rubber hose would all work. Also superglue seems to insulate.
    I will be following this thread because I need to make a new bushing for my self igniting propane torch. The spark wire comes through a metal handle casting. That bushing is a hard black plastic that cracked before. When it cracked the spark just shorted out, well below the gas flow. I took it out and super glued it back. It worked fine for a few years until I kicked the torch over and cracked the plastic. Lost a piece so I need to make a complete bushing this time. Think I will try something more flexible like nylon tubing.
    Bill D

  3. #3
    Join Date
    Apr 2004
    Location
    Modesto, CA USA
    Posts
    8,804
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    1734

    Default

    I think the first elctro magnet used wire insulated with strips of silk ripped from his wife's wedding dress. Later they would dip the wire in shellac.

  4. #4
    Join Date
    Jul 2021
    Country
    UNITED STATES
    State/Province
    Idaho
    Posts
    13
    Post Thanks / Like
    Likes (Given)
    7
    Likes (Received)
    0

    Default

    The part is rectangular and needs to be about 0.15" thick. The need for a low coefficient of thermal expansion rules out many materials that would otherwise work fine. Marble is an interesting idea and has a CTE in the right range...wonder how hard it'd be to cut some 4-40 threads in it.

  5. #5
    Join Date
    Oct 2010
    Country
    UNITED STATES
    State/Province
    Oregon
    Posts
    5,813
    Post Thanks / Like
    Likes (Given)
    5784
    Likes (Received)
    2244

    Default

    Some variants of polyimide will have thermal expansion that low, but you'll have to read spec sheets.

    Many species of wood also meet the spec, but you probably want something homogenous and isotropic, like MDF. You can laminate 1" layers of MDF, or get it in thicker sheets (harder to source).

    [Added in edit] Oh, now I see you want it thin, not thick.

  6. #6
    Join Date
    May 2009
    Location
    Canandaigua, NY, USA
    Posts
    3,415
    Post Thanks / Like
    Likes (Given)
    178
    Likes (Received)
    1733

    Default

    I think some phenolics will do that. Or, maybe something from Aremco?

  7. Likes Borealis, Ron Hofer liked this post
  8. #7
    Join Date
    Nov 2018
    Country
    UNITED STATES
    State/Province
    Michigan
    Posts
    829
    Post Thanks / Like
    Likes (Given)
    457
    Likes (Received)
    568

    Default

    Most all of the usual suspects in the plastics world will do the job if you get glass fiber reinforced versions of the polymer, it really brings the CTE down (into the 30s (x10e-6/°C) for the most part, down to the 20s for a few of them).

  9. Likes Borealis liked this post
  10. #8
    Join Date
    Mar 2007
    Location
    On Elk Mountain, West Virginia, USA
    Posts
    2,255
    Post Thanks / Like
    Likes (Given)
    1076
    Likes (Received)
    809

    Default

    Soapstone, minerological name Talc

  11. Likes Borealis liked this post
  12. #9
    Join Date
    Jun 2013
    Country
    UNITED STATES
    State/Province
    California
    Posts
    473
    Post Thanks / Like
    Likes (Given)
    383
    Likes (Received)
    199

    Default

    How about epoxy/glass?

  13. #10
    Join Date
    Dec 2008
    Location
    Vt USA
    Posts
    9,540
    Post Thanks / Like
    Likes (Given)
    1698
    Likes (Received)
    3499

    Default

    Micarta doesn't fit the bill? or G10?

  14. #11
    Join Date
    Jul 2021
    Country
    UNITED STATES
    State/Province
    Idaho
    Posts
    13
    Post Thanks / Like
    Likes (Given)
    7
    Likes (Received)
    0

    Default

    Quote Originally Posted by CalG View Post
    Micarta doesn't fit the bill? or G10?
    The CTE on phenolic-type materials tends to be closer to 100ppm/degC. I'm not sure about G10...do they make that in thicker sections? The only stuff I have in the shop is the typical 0.06" circuit board stuff...but it's glass-filled, so maybe the CTE is good.

  15. #12
    Join Date
    Jun 2013
    Country
    UNITED STATES
    State/Province
    California
    Posts
    473
    Post Thanks / Like
    Likes (Given)
    383
    Likes (Received)
    199

    Default

    I have epoxy glass (G10) in 3/4". Linear coef. = 36.

    McMaster-Carr has it in many thicknesses.

  16. #13
    Join Date
    Jul 2021
    Country
    UNITED STATES
    State/Province
    Idaho
    Posts
    13
    Post Thanks / Like
    Likes (Given)
    7
    Likes (Received)
    0

    Default

    Conrad, thanks for bringing my attention to Aremco. Never heard of them before but bookmarked it immediately after seeing all the unusual materials they offer.

    Magnetic, great idea worth looking into... Didn't know soapstone & talc are the same thing. Looks like it's easy to find online and the prices are reasonable.

    Boxcar, thanks for the suggestion to look for glass-filled versions of the plastics.

  17. #14
    Join Date
    Nov 2003
    Country
    UNITED STATES
    State/Province
    Texas
    Posts
    6,069
    Post Thanks / Like
    Likes (Given)
    219
    Likes (Received)
    2095

    Default

    I do not have a specific material to recommend, but I would urge you to be sure whatever you pick does have it's electrical resistance/conductance specified. A well respected company that built professional audio equipment ordered some plastic panels to use as terminal boards. They assumed the plastic they specified would be an insulator. Turns out it was a black color and that was produced by adding carbon powder to the mix. It drove them nuts trying to find where the cross talk was being introduced.

  18. #15
    Join Date
    Mar 2005
    Country
    UNITED STATES
    State/Province
    Indiana
    Posts
    6,438
    Post Thanks / Like
    Likes (Given)
    2279
    Likes (Received)
    2406

    Default

    Yes G-10 is made very thick. I've got some that's over an inch. And it fits the low CTE requirement.

  19. #16
    Join Date
    Feb 2014
    Location
    FL
    Posts
    4,592
    Post Thanks / Like
    Likes (Given)
    13947
    Likes (Received)
    5612

    Default

    I think PEEK fits the bill, minus the price... Although I understand the industrial grade stuff is quite a bit cheaper than the medical grade I'm used to?

  20. Likes Mike1974 liked this post
  21. #17
    Join Date
    Oct 2005
    Country
    UNITED STATES
    State/Province
    Pennsylvania
    Posts
    22,566
    Post Thanks / Like

    Default

    Glastic board ?

    Try Haysite in Erie, Pa.

  22. #18
    Join Date
    Apr 2004
    Location
    Modesto, CA USA
    Posts
    8,804
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    1734

    Default

    If it needs to be threaded it may be easier to cast it or injection mold it.
    Bill D

  23. #19
    Join Date
    Jun 2012
    Location
    Michigan
    Posts
    6,155
    Post Thanks / Like
    Likes (Given)
    5764
    Likes (Received)
    3933

    Default

    Quote Originally Posted by Borealis View Post
    I'm not sure about G10...do they make that in thicker sections?
    We have a repeat job of G10 that uses 4" thick material.
    Check out Thyssen Krupp, that's where we buy our G10 and phenolics.

    thyssenkrupp Materials NA: Materials Supplier and Supply Chain Expert

  24. #20
    Join Date
    Jun 2013
    Country
    UNITED STATES
    State/Province
    California
    Posts
    473
    Post Thanks / Like
    Likes (Given)
    383
    Likes (Received)
    199

    Default

    Here's where I buy it.

    McMaster-Carr


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •