Need help fanuc al-60 turret index power off????

F

fettersp

Aluminum

Joined

Apr 24, 2020

• Aug 19, 2020

• #1

I have a kia turn-15 with fanuc oi-t controller.
The machine was crashed yesterday and started with a z axis torque alarm. I got that freed but now have an al-60 index turret power off alarm.
The procedure im following was written down by my father and is not working.

1. change parameter 0011 to 00000001
2 turn off and on
3.set k5 bit to 1
4. push select, feed hold, and spindle stop.
5. turn turret by hand till arrows match up.
6. push call/bz off
7. set k5 bit to 0
8 push spindle stop, select, and feed hold
9. change para 0011 back to original
10. power off and on

this is not working and im not sure what to do right now

 

F

fettersp

Aluminum

Joined

Apr 24, 2020

• Aug 19, 2020

• #2

can anyone ehlp?

 

ifixcnc

Hot Rolled

Joined

Feb 6, 2015

Location

Cleveland Ohio

• Aug 19, 2020

• #3

set k5 bit to 1
K5 has 8 bits, which one are you changing?

 

F

fettersp

Aluminum

Joined

Apr 24, 2020

• Aug 19, 2020

• #4

ifixcnc said:

set k5 bit to 1
K5 has 8 bits, which one are you changing?

Click to expand...

in the instructions it says to change k5 to 1 which most likely means 00000001. After this itll allow the turret to uncouple.

 

ifixcnc

Hot Rolled

Joined

Feb 6, 2015

Location

Cleveland Ohio

• Aug 19, 2020

• #5

That would be K5 Bit 0, If the turret unclamps (uncouples) it most likely the right bit.
When you change the parameter 0011, are you turning on Parameter Write Enable?
Does the parameter show the change that you made?

 

F

fettersp

Aluminum

Joined

Apr 24, 2020

• Aug 19, 2020

• #6

yes it does change

 

F

fettersp

Aluminum

Joined

Apr 24, 2020

• Aug 19, 2020

• #7

iv also check to see if there were any tripped breakers but there are none.
The oinstructions I have are for the al60 turret index power off. These are from kia heavy industries from a long time ago

 

ifixcnc

Hot Rolled

Joined

Feb 6, 2015

Location

Cleveland Ohio

• Aug 19, 2020

• #8

When you turn the turret by hand does it move easily?
Watch the turret servo drive when you are powering the machine, does it alarm instantly?
I don't know if this current but is worth a try,
KIA Heavy Industries USA is Machine Tool Dealers company,Tel is 201-489-2887

 

F

fettersp

Aluminum

Joined

Apr 24, 2020

• Aug 19, 2020

• #9

I don't have to put in much effort to turn it.
as soon as it is turned on it will throw the alarm before I even hit standby

 

F

fettersp

Aluminum

Joined

Apr 24, 2020

• Aug 19, 2020

• #10

I tried the number and it has been disconnected

 

F

fettersp

Aluminum

Joined

Apr 24, 2020

• Aug 19, 2020

• #11

ifixcnc said:

When you turn the turret by hand does it move easily?
Watch the turret servo drive when you are powering the machine, does it alarm instantly?
I don't know if this current but is worth a try,
KIA Heavy Industries USA is Machine Tool Dealers company,Tel is 201-489-2887

Click to expand...

I don't know if I figured it out but I uncoupled the turret and spun it around about 20 times and got a turret adjust message! Now I am able to index the turret. Not sure if the problem is fixed yet though