For sale in Melbourne Florida. Both run well, are accurate and reliable. I need the room for 2 bigger machines.
1991 Fadal VMC20, 22"x16"x20" , 4th axis VH65 rotab $6500
10 hp Fanuc spindle motor and Hitachi drive. 6500 rpm. Unlike the original motor, this doesn't stall..
New X axis ball screw for a VMC 40, X axis is now 22", replaced 4 years ago
New X servo, cabling and resolver
Replaced Y axis resolver
Reballed Y and Z screws, .0001 backlash, they are not as quiet as a new screw...
Turcite resurfaced on saddle and table, bronze gibbs re scraped. original turcite replaced in 2005.
All new lube meters and much of the lube lines replaced
A axis motor and resolver replaced 18 months ago. A axis drive replaced., new cable and conduit.
Coolant pump rebuilt
New low gear shift cylinder and prox switch
Spindle bearings and drawbar springs replaced 6 years ago, low hrs since
Software was upgraded in 1996 to the highest revision for that series control
The machine had synthetic coolant in it, it ate the paint and pitted the Y axis ways. Been like that since 2005, its ugly but functional.
1982 Matsuura 760v2 $5000
X 30" Y16" Z 20"
10 hp 4500 rpm Geared 2 speed spindle-can be set for 6000rpm with a parameter change but will require spindle chiller
BT40- taper-30 tool ATC
Yasnac MX-1 control-control and machine manuals included
Fixture offsets, Macro programming
Stevens ground sub plate
2 out of 3 axis drives rebuilt, 3rd replaced
new memory board
RS232 and dnc working, comes with cable
X axis motor new bearings, coolant pump rebuilt
numerous spare control boards
Box way construction
Table guard and chip pan , coolant system has filter to catch small swarf
Machine cabinets are immaculate inside
Has some paint missing from synthetic coolant we used to use.
Spindle and axis are quiet
Parameters save to file, printed and original tape.
Vices and tooling not included
I have a 4th axis control card for it if you have the skills....
You cannot stop the spindle on this tank.....pure torque
View attachment 291500View attachment 291501
I have lots of pictures, for more info email me at [email protected]
These are solid machines that were taken care of. They were run, but not beat and not crashed. They gotta go and we can probably get them rigged out reasonably when my new stuff gets here.
1991 Fadal VMC20, 22"x16"x20" , 4th axis VH65 rotab $6500
10 hp Fanuc spindle motor and Hitachi drive. 6500 rpm. Unlike the original motor, this doesn't stall..
New X axis ball screw for a VMC 40, X axis is now 22", replaced 4 years ago
New X servo, cabling and resolver
Replaced Y axis resolver
Reballed Y and Z screws, .0001 backlash, they are not as quiet as a new screw...
Turcite resurfaced on saddle and table, bronze gibbs re scraped. original turcite replaced in 2005.
All new lube meters and much of the lube lines replaced
A axis motor and resolver replaced 18 months ago. A axis drive replaced., new cable and conduit.
Coolant pump rebuilt
New low gear shift cylinder and prox switch
Spindle bearings and drawbar springs replaced 6 years ago, low hrs since
Software was upgraded in 1996 to the highest revision for that series control
The machine had synthetic coolant in it, it ate the paint and pitted the Y axis ways. Been like that since 2005, its ugly but functional.
1982 Matsuura 760v2 $5000
X 30" Y16" Z 20"
10 hp 4500 rpm Geared 2 speed spindle-can be set for 6000rpm with a parameter change but will require spindle chiller
BT40- taper-30 tool ATC
Yasnac MX-1 control-control and machine manuals included
Fixture offsets, Macro programming
Stevens ground sub plate
2 out of 3 axis drives rebuilt, 3rd replaced
new memory board
RS232 and dnc working, comes with cable
X axis motor new bearings, coolant pump rebuilt
numerous spare control boards
Box way construction
Table guard and chip pan , coolant system has filter to catch small swarf
Machine cabinets are immaculate inside
Has some paint missing from synthetic coolant we used to use.
Spindle and axis are quiet
Parameters save to file, printed and original tape.
Vices and tooling not included
I have a 4th axis control card for it if you have the skills....
You cannot stop the spindle on this tank.....pure torque
View attachment 291500View attachment 291501
I have lots of pictures, for more info email me at [email protected]
These are solid machines that were taken care of. They were run, but not beat and not crashed. They gotta go and we can probably get them rigged out reasonably when my new stuff gets here.
