FS Brown and sharpe 510 surface grinder
Close
Login to Your Account
Results 1 to 12 of 12
  1. #1
    Join Date
    Sep 2009
    Country
    UNITED STATES
    State/Province
    Virginia
    Posts
    152
    Post Thanks / Like
    Likes (Given)
    30
    Likes (Received)
    21

    Default FS Brown and sharpe 510 surface grinder

    Running out of room in the shop,time to thin the herd.Brown and sharpe 5"by 10" manual surface grinder with Yuasa fine pole chuck.Roller bearing table,dust collector,has some backlash in y axis.220 3 phase.1500.00 cash no paypal.Pick up in Clover Virginia,will load for free.More than happy for you to try it out. [email protected] or PM any questions.
    Attached Thumbnails Attached Thumbnails img_20210914_104341100.jpg   img_20210914_104403284.jpg   img_20210914_104358201.jpg  

  2. Likes rpseguin, ncjeeper, shapeaholic liked this post
  3. #2
    Join Date
    Jun 2006
    Country
    UNITED STATES
    State/Province
    California
    Posts
    1,238
    Post Thanks / Like
    Likes (Given)
    1228
    Likes (Received)
    196

    Default

    California is the next state over from Virginia, right? :-)
    Looks nice!
    I’m looking for a small surface grinder, just wish it were within driving range!

  4. Likes boomerang69 liked this post
  5. #3
    Join Date
    Sep 2009
    Country
    UNITED STATES
    State/Province
    Virginia
    Posts
    152
    Post Thanks / Like
    Likes (Given)
    30
    Likes (Received)
    21

    Default

    You'd have to pack 2 coolers for that trip

  6. Likes rpseguin liked this post
  7. #4
    Join Date
    Sep 2006
    Location
    Stillwater, Oklahoma
    Posts
    1,935
    Post Thanks / Like
    Likes (Given)
    156
    Likes (Received)
    1166

    Default

    The big crank is the L-R table traverse? Haven't seen that before but it sounds workable enough on a smaller travel machine.

  8. #5
    Join Date
    Sep 2009
    Country
    UNITED STATES
    State/Province
    Virginia
    Posts
    152
    Post Thanks / Like
    Likes (Given)
    30
    Likes (Received)
    21

    Default

    it gives full table traverse in very little effort,its one of the reasons I bought it.

  9. #6
    Join Date
    Jan 2015
    Country
    UNITED STATES
    State/Province
    Virginia
    Posts
    190
    Post Thanks / Like
    Likes (Given)
    123
    Likes (Received)
    33

    Default

    Now you post this. Been looking for a SG in very good shape. Just went all the way to Florida 2 weeks ago to pick up a Harig.

  10. #7
    Join Date
    Jun 2012
    Country
    UNITED STATES
    State/Province
    Michigan
    Posts
    14,336
    Post Thanks / Like
    Likes (Given)
    4885
    Likes (Received)
    5182

    Default

    Nice grinder, the hand crank is handy.
    The zero lock for down feed is handy.
    It is hard to beat a B&S grinder.

  11. Likes boomerang69 liked this post
  12. #8
    Join Date
    Sep 2009
    Country
    UNITED STATES
    State/Province
    Virginia
    Posts
    152
    Post Thanks / Like
    Likes (Given)
    30
    Likes (Received)
    21

    Default

    Thats my luck

  13. #9
    Join Date
    Feb 2008
    Location
    Hertford, NC
    Posts
    24
    Post Thanks / Like
    Likes (Given)
    0
    Likes (Received)
    1

    Default

    What kind of height are we taking about? Also, if you needed to get it through an 80" high door, is it possible and practical to remove items to lower it sufficiently? Thanks.

  14. #10
    Join Date
    Sep 2009
    Country
    UNITED STATES
    State/Province
    Virginia
    Posts
    152
    Post Thanks / Like
    Likes (Given)
    30
    Likes (Received)
    21

    Default

    I will be in the shop tommorow and take some measurements
    Thanks

  15. #11
    Join Date
    Sep 2009
    Country
    UNITED STATES
    State/Province
    Virginia
    Posts
    152
    Post Thanks / Like
    Likes (Given)
    30
    Likes (Received)
    21

    Default

    I sent you a PM

  16. #12
    Join Date
    Sep 2017
    Country
    UNITED STATES
    State/Province
    New Jersey
    Posts
    379
    Post Thanks / Like
    Likes (Given)
    5
    Likes (Received)
    112

    Default

    Quote Originally Posted by cdustercc View Post
    What kind of height are we taking about? Also, if you needed to get it through an 80" high door, is it possible and practical to remove items to lower it sufficiently? Thanks.
    B&S 510, if you unscrew the shield for the vertical height screw can be 75" tall, with the
    head lowered most of the way.

    You could remove it from the base cabinet (3 bolts from inside the base) but no need to do that. Note: the column is held in place only by the leadscrew and the dovetails, so make sure you take that into account when you move one, to avoid damaging the nut or bending the screw.


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •