What's new
What's new

Drafting and Measure Up Tool Box.

AussiePete

Plastic
Joined
May 3, 2020
Always refered to this as My Drafting and Measure Up Tool Box...On site Measurements taken with steel calibrated Instruments,Design and Drafting back at the shed.
 

Attachments

  • 1-Top Tray (5) (2019_06_05 02_18_02 UTC).jpg
    1-Top Tray (5) (2019_06_05 02_18_02 UTC).jpg
    101.6 KB · Views: 170
  • IMG_3968.jpg
    IMG_3968.jpg
    92.1 KB · Views: 158
  • IMG_3966.jpg
    IMG_3966.jpg
    93.6 KB · Views: 218
  • 4-Draw 3 (1) (2019_06_05 02_18_02 UTC).jpg
    4-Draw 3 (1) (2019_06_05 02_18_02 UTC).jpg
    100.2 KB · Views: 146
  • 1-Top Tray (4) (2019_06_05 02_18_02 UTC).jpg
    1-Top Tray (4) (2019_06_05 02_18_02 UTC).jpg
    101.3 KB · Views: 126
Always refered to this as My Drafting and Measure Up Tool Box...On site Measurements taken with steel calibrated Instruments,Design and Drafting back at the shed.

"Waltzin' Matilda.. wal....."

Met your type before. Carry a tall clock about instead of wearing a wrist-watch.

Scary part is all them heavy, sharp obects in the kit and nary even a scrap of note-paper.

You SURE you ain't one of them travlin' gypsy-type lads as does free-lance circumcisions, castrates sheep, docks puppy-dog tails, and cures farmer's daughters of the monthlies for nine months at a go?

:D
 
Aussie lunch......You SURE you ain't one of them travlin' gypsy-type lads as does free-lance circumcisions, castrates sheep, docks puppy-dog tails, and cures farmer's daughters of the monthlies for nine months at a go?....Boys will be Boys....1:01PM Back to Work...Cheers.
 
"Waltzin' Matilda.. wal....."

Met your type before. Carry a tall clock about instead of wearing a wrist-watch.

Scary part is all them heavy, sharp obects in the kit and nary even a scrap of note-paper.

You SURE you ain't one of them travlin' gypsy-type lads as does free-lance circumcisions, castrates sheep, docks puppy-dog tails, and cures farmer's daughters of the monthlies for nine months at a go?

:D
YouTube
 
Aussie lunch......You SURE you ain't one of them travlin' gypsy-type lads as does free-lance circumcisions, castrates sheep, docks puppy-dog tails, and cures farmer's daughters of the monthlies for nine months at a go?....Boys will be Boys....1:01PM Back to Work...Cheers.

Kinda miss the days when we-all would make a few pencil scratch dimensions on a 3x5 file card, carry-away all-else 'tween the ears, "JFDI" and come back with the part as "fit right up, first go", THAT job was DONE.... and on to the next.

Now? Dozen fotos into a hand-held .. haul the part off to some other Pilgrim with a "CMM" ... crank an insane buncha numbers inta OTHER number-crunching dirty beach sand... run a Metric TON of bloated "packets" all over various "networks", adjust the piss outta "wire frame" models on glass drawing board, tweak "G Code" by hand....

... and end up makin'the "pilot model" part inside-out and backwards, first run off a 3-D printer...

Figure we might have LOST sumthin' useful about "visualization" to the level we can't even put a proper exit taper on the clean end of our own turd without the help of "electronics"?

Must be so. My age? I just radius that s**t.
 








 
Back
Top