Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Jay Fleming

Page 1 of 35 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    11
    Views
    1,735

    I'm not sure Carlisle would be interested based...

    I'm not sure Carlisle would be interested based on our suspected quantities.
  2. Replies
    11
    Views
    1,735

    I have already sent them a request but haven't...

    I have already sent them a request but haven't heard back.
  3. Replies
    11
    Views
    1,735

    I'm not sure either would be interested. The...

    I'm not sure either would be interested. The plating is probably the one item that would be okay outsourced. I'm just trying to avoid having one shop that can do the stamping of the male contact,...
  4. Replies
    11
    Views
    1,735

    I will look at both of these.

    I will look at both of these.
  5. Replies
    11
    Views
    1,735

    I looked at their website but haven't contacted...

    I looked at their website but haven't contacted them. I've talked to 10 or so shops already and just trying to expand my list. I don't have more detailed information available right now. Just trying...
  6. Replies
    11
    Views
    1,735

    Electrical Contacts to be Manufactured...

    I have the contacts in the attached picture that we're looking for vendors for. This is federal government work. I'm not sure if this project will require going out on FBO or we can get a certain...
  7. I am no longer needing these parts. Sent from...

    I am no longer needing these parts.

    Sent from my SM-G960U using Tapatalk
  8. If they'll both fit the same external spline,...

    If they'll both fit the same external spline, either is fine.

    Sent from my SM-G960U using Tapatalk
  9. A couple people asked about shaping, which is...

    A couple people asked about shaping, which is fine. I specifically asked for broaching because of the assumed economics. WEDM is also fine, but again, I'm not looking to spend a fortune because...
  10. No problem, thanks though. I've got a local shop...

    No problem, thanks though. I've got a local shop I can ask but just wanted more options.

    Sent from my SM-G960U using Tapatalk
  11. Broached mild steel coupling - 1.25 - 19 16/32 inv splines

    No drawing available.

    1018 mild steel okay, cold rolled round bar, 2.00" OD stock, mill OD finish fine.

    1.50" +/- .015 long, .030-.060 x 45 deg chamfer on OD and ID - chamfer dims not critical,...
  12. I have chosen a vendor for this. No more bids...

    I have chosen a vendor for this. No more bids will be accepted. Thank you to all who have sent quotes.

    Sent from my SM-G960U using Tapatalk
  13. The planet carrier in the picture technically has...

    The planet carrier in the picture technically has 9 holes, but I'm referring to the ring gear, which isn't shown, that will get 12 holes.

    Sent from my SM-G960U using Tapatalk
  14. RFQ: 1 4140HT planet carrier, 1 modified ring gear

    Email jaymfleming at gmail dot com for prints. I tried to attach them but they're slightly too large for a PDF.

    I need a quote for one planet carrier and one hole pattern machined in the ring...
  15. I can't edit my original post. The drill chuck,...

    I can't edit my original post. The drill chuck, tool setter, pro tram, dial indicator spoken for.

    Sent from my SM-G960U using Tapatalk
  16. I tried sending you a PM but your box is full....

    I tried sending you a PM but your box is full. Try clearing and resending your shipping info, along with when it's okay to ship. I think your settings might have caused a sent message to try and be...
  17. I sent you an email but these items are spoken...

    I sent you an email but these items are spoken for.

    Sent from my SM-G960U using Tapatalk
  18. No takers yet? Sent from my SM-G960U using...

    No takers yet?

    Sent from my SM-G960U using Tapatalk
  19. Maritool CAT40 holders, Edge Technology tool setter, pro tram, Mitutoyo indicator

    All prices OBO but don't low ball. Deals will be given for multiple items. Free shipping over $200. USPS Flat rate insured exact cost otherwise. Reply here or PM with additional questions or...
  20. I can't edit my original post any longer but the...

    I can't edit my original post any longer but the following annular cutters are sold:
    3/4 x 3 (not previously listed)
    (1) 7/8 x 3
    1 x 2
    1-1/16 x 3
    1-1/8 x 2 TiN
    1-1/4 x 2
  21. All of them have 3/4 shanks. Sent from my...

    All of them have 3/4 shanks.

    Sent from my SM-G960U using Tapatalk
  22. All listed cutters that dont specifically say...

    All listed cutters that dont specifically say (needs sharpening) are ready to use. They're used, but still cut good. Sneebot sent me a PM on the vise jaws, so they're his.

    Sent from my SM-G960U...
  23. Haimer 3D Taster, Edge Technology tools, Maritool Holders, Annular Cutters

    Getting out of machining and want to liquidate my tools. All prices are OBO. I have a lot of other stuff, these were just the most accessible. Paypal payment preferred. Shipping will be USPS, most...
  24. Yes but not on anything that large. I've marked...

    Yes but not on anything that large. I've marked non-critical features on indexed parts, when I didn't have an indexer.

    Sent from my SM-G960U using Tapatalk
  25. Instead of marking out the circumference, how...

    Instead of marking out the circumference, how about marking out the straight length between two posts? Then keep moving around. If you end up 2" off when you measure from post 8 to post 1, add or...
Results 1 to 25 of 860
Page 1 of 35 1 2 3 4