Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Illinoyance

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    15
    Views
    718

    Roll a cylinder from sheet.

    Roll a cylinder from sheet.
  2. Replies
    2
    Views
    347

    Check with Brownells. Their 3.5% nickel rod is...

    Check with Brownells. Their 3.5% nickel rod is supposed to take color case hardening.
    BROWNELLS 3 1/2% NICKEL STEEL WELDING ROD | Brownells
  3. With that hole below the spindle I would say that...

    With that hole below the spindle I would say that is the base for a reamer grinding attachment. The rod projecting from that hole would have mounted a dead center. As to the fix of the broken...
  4. I have a couple spa pumps with 2 speed motors I...

    I have a couple spa pumps with 2 speed motors I want to get rid of.
  5. Replies
    2
    Views
    325

    There is a wealth of information in these old...

    There is a wealth of information in these old books. Much of it has been forgotten.
    Thanks for the link.
  6. These are near what you want. Thin Parallels, 3"...

    These are near what you want.
    Thin Parallels, 3" Long, 11 Pairs 3946 - LittleMachineShop.com
  7. Replies
    3
    Views
    800

    Try here:...

    Try here:
    https://www.leevalley.com/en-us/shop/general/catalog/47025-hardware-catalog
  8. The micrometer works even better is held in a...

    The micrometer works even better is held in a stand.
  9. You need a 5C fixture mount. Victor Machinery -...

    You need a 5C fixture mount.
    Victor Machinery - Metalworking tools and supplies
  10. Coparator stand with dial indicator or snap gauge.

    Coparator stand with dial indicator or snap gauge.
  11. I would like to see a photo of the Atlas X-Y...

    I would like to see a photo of the Atlas X-Y rotary table.
  12. Don't even try to remember it. Get it on paper...

    Don't even try to remember it. Get it on paper or bookmark a web page. If I recall Machinery's Handbook has that info. Make up a binder of frequently needed information.
  13. Replies
    15
    Views
    1,340

    I don't think the substitution of yards for...

    I don't think the substitution of yards for meters was a cost saving shortcut.The diameters in the chart are in inches.
  14. I got some N95s from Amazon. $5 each.

    I got some N95s from Amazon. $5 each.
  15. Replies
    24
    Views
    2,035

    I own 0-1 and 1-2 thread mikes with...

    I own 0-1 and 1-2 thread mikes with interchangeable anvils. I would never consider using wires in the 0 to 2" range. The convenience of thread mikes makes them worth the investment.
  16. Replies
    10
    Views
    757

    If the callout is for BSPP the mating fitting...

    If the callout is for BSPP the mating fitting would have a flange that seals against the face of the part by means of a copper gasket. BSPP stands for British Standard Parallel pipe.
  17. The toolpost is labeled Mecanizados Huesca MH90 ...

    The toolpost is labeled Mecanizados Huesca MH90 It measures 90mm wide 68.1mm high, c-c of the Vs is approximately 69.3mm. There are 4 tool holders with the toolpost.
  18. With the Heath you will need individual templates...

    With the Heath you will need individual templates for the circles.
  19. Replies
    34
    Views
    1,787

    That variation is likely caused by worn...

    That variation is likely caused by worn components on the transfer line where the block was machined.
  20. Replies
    6
    Views
    621

    They look like the clips used to fasten elevator...

    They look like the clips used to fasten elevator guide rail to the brackets.
  21. I have a Dickson with a few holders. Not sure...

    I have a Dickson with a few holders. Not sure what size it is. I will measure it tomorrow and try to find Dickson specs so I can identify the size.
  22. Replies
    22
    Views
    2,453

    The primary attributes of a "gunsmith lathe" are...

    The primary attributes of a "gunsmith lathe" are a short headstock and a spindle bore large enough to pass a barrel plus a spider on the left end of the spindle. Most are imports of dubious quality....
  23. Replies
    10
    Views
    874

    Dayton seems to be the name for many products...

    Dayton seems to be the name for many products from Grainger. I can't look up all the things with the Dayton name because I threw away my Grainger catsalog. Too damn expensive.
  24. Replies
    9
    Views
    709

    It looks like that red block is pulled sideways...

    It looks like that red block is pulled sideways to clamp the right dovetail to the ram.
  25. I machined a sleeve to do just that. I used a...

    I machined a sleeve to do just that. I used a very sharp HSS tool. As I remember it was from some kind of plastic.
Results 1 to 25 of 1494
Page 1 of 60 1 2 3 4