Search:

According to Larry in post #4 the ones with the slot in the knurled part have return springs. The others do not.


Sent from my iPhone using Tapatalk

Those are nice, but quite a bit larger than the originals. On the Gits site, which you linked to, they show a cross section drawing. You can see the screw slotted part is part of the main body....

Digging up a 10 year old thread. I need a couple of these rotating sleeve oilers with 10-32 thread. Unfortunately Larry’s link to a source is no more. Not a surprise. I’m thinking of making a couple...

Thanks for all the input folks. The panel is Square D QO. On Saturday while trying to switch on the transformer the 200A main tripped and stayed stuck in the tripped position. Would not turn off...

Yes, that's what I want. This is helpful, thanks. But I'm having trouble converting this to a product or part number. My transformer is 45kVA, so I want a 60HP soft starter? Sound right? Is it...

When I was working in Camarillo there was a shop behind us that did Al spinning. I used to watch sometimes during lunch. They turned the metal pretty slow, like half the speed you'd use if you were...

Care to make a specific suggestion?

Dealing with a similar problem discussing in another thread. Does someone have a link to a "soft start" device that would work in this application?

Would a "soft start" device work in this application? From the description of the device it seems like it would, but I only see them discussed in regards to a motor, not a transformer.

My shop has 208V 200A 3PH service panel. I’ve got several 480V machines that I supply through the following transformer:...

After having a shop for several years I eventually picked up a horizontal band saw for cutting stock to length. Ever since I've wondered how I ever got along without it and why didn't I buy that...

Update, the serial number on the lathe is 72171-50 making it a 1950 per John O. Another PM member sent me a chart showing the weight to be 5400 lbs. Looks heavier. The truck is a 2000 GM super duty...

It doesn’t have any issues. In fact I cut some metal on it Friday morning. It was in the local foundry auction a month ago but didn’t get picked up. It was about to get turned over to the scrappers...

Going to scrap this week. Any interest? I think scrap is around $800 on this.
https://uploads.tapatalk-cdn.com/20201219/43d55087c8482c0488219ebf63a7d472.jpg


Sent from my iPhone using Tapatalk

No. It’s one or the other. Mine is monoset and I haven’t had the problems people are claiming. You only need a few sizes. By eighths is plenty. The collets are available here and there and aren’t all...

Deckel cabinet here
https://uploads.tapatalk-cdn.com/20201217/846b39129fa7ed6f184e6d3225ffb4d8.jpg

The lower door track has a notch that allows the door to drop into the track. The upper door...

What spindle on the Cincinnati? They used the monoset collet but were also available with 40 taper. Either way it’s a much better mill than the round ram Bridgeport.


Sent from my iPhone using...

Yes they do. I bought 400 feet of it.


Sent from my iPhone using Tapatalk

I’ve moved 4 10Ees, two across the country. I did not remove the tubes and never had a problem. I think there is more risk in the rigger removing the tubes and damaging/losing them in the process. I...

Normally the rule is that equipment must be supplied with all required safety gear and the user must keep all that safety gear in use and operable. So if it's not currently required they don't have...

I made mine out of 4140 pre hard. Get a piece 1 1/4 x 8. Machine the back of the finger on each side then slice it at a 45 down the center to get two pieces. Keep one as a single 24” piece and chop...

Lower the upper storage area by two inches.


Sent from my iPhone using Tapatalk

You came by after 11 years just to tell me I’m wrong? Are you my daughter?


Sent from my iPhone using Tapatalk

Thanks guys I got it. There are templates that are blank sheets, just had to dig in the right place, kind of along the lines of Mud's suggestion.

I want to send some parts to Oshcut but can't see how to save only the part without the border, frame, and title block.